Parts for Ge DSHF6VGBBCWW: 01 - Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.

The handle fastener secures your refrigerator door handle to the door panel and provides structural support. Replace when the handle becomes loose, wobbles excessively, or the fastener shows signs of cracking or stripping.

This white stop door replaces the dispenser stop/door that controls access to the ice/water chute, helping restore proper dispenser operation and reduce sticking or unwanted discharge. Designed to match the original OEM fit and appearance. What it does

• Seals and releases the dispenser opening so ice or water is dispensed only when the door is actuated
• Replaces a cracked, warped, or jammed stop door that can cause sticking or partial openings
• Helps prevent accidental drips or debris entering the dispenser chute
• Restores a smooth, aligned door movement for reliable dispensing

• One white stop door

• Disconnect power to the appliance before starting any repair
• Remove dispenser housing or outer door per the service manual to access the stop door
• Inspect the actuator and mounting tabs for damage; replace if worn to ensure proper operation
• Use basic hand tools;

Stops refrigerator door from opening past 90 degrees. Mounts at base of door with screws. Replace if cracked, broken, or bent to prevent door overswing.

Seals freezer door to prevent frost buildup and air leaks. Replace if torn, warped, or causing moisture issues. Verify fit with your model number.

Seals freezer door to prevent warm air entry and cold air loss. Replace if torn, cracked, or causing frost buildup. Confirm fit with your model number.

White plastic cam closure that aligns and secures the freezer door in the hinge area. Replace if cracked, broken, or worn to restore proper alignment.

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

This module shelf supports and secures the freezer control module or related electronics, keeping components stable and properly positioned for reliable operation. Fits into the freezer compartment to help prevent vibration and contact damage. What it does:

• Provides a stable mounting surface for the freezer control module or electronics assembly
• Keeps wiring and small components organized and away from cold airflow
• Reduces vibration and movement that can cause intermittent electrical issues
• Helps prevent physical damage from loose parts inside the freezer compartment

• One module shelf

• Disconnect power to the appliance before servicing to avoid shock or injury
• Inspect and reuse existing mounting hardware if not explicitly supplied

Replace your refrigerator's dispenser drip tray if cracked, stained, or missing. Catches water and ice drips in the dispenser recess for a clean look.

Replacement dispenser grill recess drip tray for side-by-side refrigerators. Collects spills and overflow in the dispenser area. Replace if cracked or missing.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Fix a damaged or cracked dispenser front with this housing shield. Protects internal components and restores a finished look to your refrigerator's exterior.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.

This white ice dispenser paddle is the lever you press on the freezer door to release ice. Replacing a worn or broken paddle restores reliable ice dispensing and a clean, like-new look at the dispenser.

• Transfers your push to the dispenser switch to start ice delivery
• Helps fix a cracked, broken, loose, or missing paddle
• Addresses a lever that sticks or doesn't return smoothly
• Useful when ice won't dispense unless the switch is pressed directly
• Refreshes a yellowed or scuffed dispenser paddle

• Disconnect power to the refrigerator before servicing
• Remove the drip tray and dispenser trim/control panel to access the paddle
• Note spring/lever orientation and transfer any hardware from the original paddle
• Reassemble, restore power, and test ice dispensing

Replacement paddle for refrigerator ice dispenser. Press to activate ice release. Replace if cracked, broken, or won't spring back after pressing.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Protective cover that shields the LED light assembly in your refrigerator. Replace this housing if cracked, broken, or missing to restore proper coverage.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Replaces a broken, cracked, or missing freezer shelf module in side-by-side refrigerators. Installs in factory side supports for organized storage.

This fixed freezer module shelf supports and secures the freezer module assembly, restoring stable storage and preventing items from shifting or contacting the module. It's a direct replacement for a cracked, warped, or missing shelf. What it does:

• Holds and supports the freezer module assembly so it stays properly positioned.
• Keeps stored items from contacting or damaging the module.
• Replaces shelves that are cracked, broken, or bent and that allow items to slide or fall.
• Reduces rattling or movement caused by a loose or broken shelf.

• Disconnect power to the refrigerator before servicing to prevent electrical hazard.
• Empty the freezer area and remove loose shelves or bins that block access.
• Align the shelf with its mounting points and seat it gently; do not force or modify the part.
• If fasteners are present, reuse OEM fasteners or replace with manufacturer-specified hardware.

SCR solid-state switching module that controls power flow in refrigerator circuits. Replace when module is damaged, burned out, or failing to switch properly.

Wiring harness for the recessed dispenser area of your refrigerator. Replace if wires are damaged, frayed, or connections are loose or corroded.

Outer door panel foam assembly for refrigerator doors. Replaces cracked, damaged, or worn door panels. Restores door appearance and insulation.

Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Door hinge thimble for side-by-side refrigerators. Installs on the door hinge assembly. Replace if cracked, broken, worn, or missing for proper alignment.

Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.