Parts for Ge ZISP480DKCSS: Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Assorted fasteners for securing refrigerator trim, panels, and components. Replace missing, stripped, or damaged screws and clips for proper assembly.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Plastic housing shield that covers and protects the refrigerator dispenser assembly. Replace if cracked, warped, broken, or missing for a secure fit.

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.

Fix a broken or unresponsive ice/water dispenser with this refrigerator door paddle. Restores the lever you press to activate dispensing functions.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Fix dispenser lights not working or unresponsive touch controls. This glass touch dispenser assembly restores water and ice dispensing on your refrigerator.

Replacement top hinge assembly for side-by-side refrigerator freezer doors. Needed when the hinge is cracked, broken, or worn causing door misalignment.

Bottom hinge bushing for refrigerator freezer doors. Installs at the lower hinge to help the door pivot smoothly. Replace if worn, cracked, or missing.

Door gasket and label assembly creates an airtight seal to keep cold air in and moisture out. Replace when worn or damaged to restore efficiency. Verify fit.

Flip-up cover for refrigerator door bin compartments. Replace cracked, broken, or missing covers to keep items contained and restore a finished look.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Bottom door hinge for refrigerators and freezers. Secures and supports the lower door edge. Replace if cracked, bent, or worn to restore proper alignment.

This stainless steel hex cap screw fastens appliance panels and components where a 1/4-20 threaded fastener is required. Durable corrosion-resistant finish helps maintain secure mounting and reliable operation. What it does

• Secures panels, brackets, and internal components to frame or chassis.
• Replaces stripped, rusted, or missing mounting screws that cause loose or rattling parts.
• Restores proper alignment and prevents movement that can lead to wear or noise.

• Use the correct 1/4 in hex socket or wrench; avoid rounded or worn tools.
• Tighten until snug; do not over-torque — overtightening can strip threads or crack plastic parts.
• Replace any damaged mating hardware (nuts, clips, or threaded inserts) for a secure fit.
• Power tools may be used carefully on low torque settings to avoid over-driving.

Size: 8-16 x 2 inch ss.

Connects refrigerator water supply tubing to the appliance for dispenser and ice maker. Replace if cracked, loose, damaged, or leaking at the connection point.

Set screw for freestanding freezers and refrigerators. Secures internal components and panels. Replace if screw is stripped, missing, or damaged.