Parts for Ge MSG22GRXAWW: 02 - Freezer Section Parts

This breaker strip trim installs along the freezer section edge of your refrigerator. Replace if cracked, broken, or missing to restore appearance.

Breaker strip trim for top freezer compartment door. Replace if cracked, broken, or missing to restore door seal and cabinet finish appearance.

Bottom freezer door breaker strip for refrigerators. Seals the gap between door sections. Replace if cracked, broken, or missing for proper fit.

This shelf support secures an interior refrigerator shelf in place so food items stay level and storage remains organized. It replaces a cracked or worn support to restore proper shelf seating and stability. What it does

• Holds a refrigerator shelf or shelf trim in the correct position to prevent sagging or tipping
• Restores stable support for glass or wire shelving that no longer stays seated
• Helps eliminate shelf movement that can cause items to slide or spill
• Works where a broken, chipped, or missing support prevents proper shelf alignment

• Disconnect power to the appliance before starting any repair and empty the shelf area
• Remove the affected shelf or trim to access the support; reinstall shelf to confirm correct seating
• Use basic hand tools as needed and avoid forcing parts to prevent further damage
• Replace all affected pieces for consistent shelf alignment

Refrigerator not cooling but freezer works? Frost buildup on back wall? Your evaporator may need replacement. Moderate difficulty repair for most models.

Fix frost buildup and icing issues in your refrigerator with this defrost heater harness assembly. Includes thermostat for reliable defrost cycles.

Plastic plug fastener insert for your refrigerator. Secures panels and covers in place. Replace if cracked, broken, or missing to restore proper fit.

Fridge not cooling but freezer works? Ice buildup on evaporator coils? This defrost thermostat regulates defrost cycles. Easy 5-15 minute DIY fix.

Replaces broken or worn lower door hinge assembly on your refrigerator. Restores proper door alignment and smooth pivot action. Includes cams for installation.

Replacement roller wheel for refrigerator drawers and bins. Installs on rear guide rails. Replace when worn, cracked, or causing sticking movement.

Wire harness for refrigerators. Connects electrical components inside the unit. Replace if wires are frayed, damaged, or connections are loose or corroded.

Replaces the outer housing that supports your refrigerator's ice crusher and dispenser chute. Order a new housing if yours is cracked or broken.

This replacement part is an ice dispenser deflector, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice dispenser deflectors are found inside of the ice-making assembly and are an important part of many freezers. The ice dispenser deflector allows the ice to come down from the tray into the dispensing area. A new ice dispenser deflector might be needed if the current one has become too brittle and has even cracked or broken. Be sure that the refrigerator is completely powered off before starting this repair. The user must have access to the ice maker assembly and will need common household tools like a screwdriver and pliers. The user might also need working gloves as some parts in and around the assembly have sharp edges or blades.Note that this part is sold individually. This ice dispenser deflector is sourced directly from the manufacturer and is a genuine OEM replacement part.

Ice won't crush or dispenses slowly? This refrigerator ice crusher auger blade assembly moves and crushes ice for proper dispensing. Easy DIY fix.

Mounting spacer maintains proper clearance between refrigerator panels, doors, or components. Replace if cracked, broken, or missing to restore fit.

Supports and centers the ice crusher blade assembly in your refrigerator. Replace if cracked, worn, or missing to prevent blade wobble and noise.

Ice not dispensing or auger jammed? This rear ice dispenser helix connects the motor to the crusher blade. Moderately easy DIY fix for most models.

This replacement part is an ice auger blade, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice auger blades are usually found in ice maker assemblies and are used during the ice-making and dispensing process. These blades are what are used when the user is in need of shaved or crushed ice. The mechanism takes full ice cubes and cuts the ice cubes down to create the different types of ice. A new ice auger blade might be needed if the user noticed that the current blades are dull or unable to cut ice. It is possible that the blades become dull over time after many years of use, so replacing them might be a good idea. Be sure the power is completely off before attempting to repair this part.This ice auger blade is sourced directly from the manufacturer and is a genuine OEM replacement part. Note that this part is sold individually.

The Drive Cup is an OEM part for GE refrigerators. This part engages with other parts to drive the ice out of the molds and into the storage bin.  

Causes of Drive Cup failure can range from physical wear and tear from regular use, which may lead to cracks or deformities in the part, to accumulation of frost or ice that hinders its movement.  

Symptoms of a malfunctioning Drive Cup include:

• The ice maker fails to eject ice properly, leading to clogs or jams within the system.
• Unusual noises during the ice-making cycle, which could indicate that the drive cup is not engaging correctly with other components.
• Decreased efficiency in ice production, as the mechanism struggles to operate smoothly.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the ice container only.

Seals the ice bucket to prevent spills, frost buildup, and water pooling. Replace when ice shifts or water collects. Confirm fit with your model.

This part has been discontinued and is no longer available.

Secures glass shelves in place to keep food organized and prevent sagging. Replaces cracked, broken, or worn brackets that no longer hold shelves level.

Includes 12 clips.

Drives the auger to push ice from bin to chute. Replace if ice won't dispense or motor jams. Verify fit with your model number before ordering.

This part has been discontinued by the manufacturer and is no longer available.

Mounting bracket that secures the ice dispenser solenoid in place. Replace if cracked, broken, or missing to restore proper solenoid alignment and function.

Fix a refrigerator that won't dispense water or make ice with this water inlet valve solenoid assembly. Direct replacement part for select models.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser only making crushed ice instead of cubes? This solenoid valve kit fixes the cube/crushed ice selector. Easy DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Replacement ice bucket door for refrigerators. Covers the ice storage bin opening. Order when your original door is cracked, broken, or missing.

Fix electrical connection issues in your refrigerator with this terminal block socket assembly. Connects power to components. Moderate DIY repair.

Illuminates refrigerator and freezer compartments for visibility. Replace when dim, flickering, or burned out. Verify fit with your model number.

Package of 12

Mounting screw for securing range components and panels. Replace if missing, stripped, or corroded. Package includes 12 screws for installation.

Freezer not cooling or making buzzing noise? The evaporator fan blade circulates cold air. Easy DIY fix in under 5 minutes—simply pull off and press on.

The Fan Blade Grommet is an OEM replacement part for GE brand refrigerators. Located behind the evaporator fan blade where its central shaft passes through, this rubber sealing piece creates a protective barrier isolating the fan assembly.

Causes of a potentially problematic fan blade grommet include cracks or deterioration that develop from continuous vibration and impacts over extended use. Exposure to temperature fluctuations can also cause the rubber to harden and lose elasticity. 

Symptoms of a faulty fan blade grommet include:

• Airflow obstructions within the duct 
• Noisy vibrations from the fan assembly
• Rubber debris collecting on components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore model refrigerators.

Ice maker stopped producing ice? This 220V ice maker assembly restores ice production in compatible refrigerators. Replaces broken stripper fingers.