Parts for Ge PSHS9PGZBCSS: 07 - Fresh Food Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Size: 10-32 GXTT FLP.595 S

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.

Air return grille installs at the bottom of the fresh food compartment behind the drawers. Replace if cracked, broken, or missing after cleaning.

Plastic cover that protects the damper assembly inlet/discharge area in your refrigerator. Replace if cracked, broken, or tabs are damaged.

Secures refrigerator panels, brackets, and trim. Replace if screw is stripped, missing, or no longer holds components tightly in place.

Rubber grommet secures the base grille on your refrigerator. Replace if cracked, worn, or missing to restore a snug fit and reduce vibration or rattle.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the hars

Protects and diffuses your refrigerator's interior LED lighting. Replace when cracked, yellowed, or missing to restore proper light distribution.

Replace your worn or broken refrigerator bottom hinge pin. Supports the door and serves as the lower pivot point on the bottom hinge assembly.

Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.

LED light board assembly illuminates refrigerator interior. Replace when lights dim, flicker, or fail to turn on. Verify fit with your model number.

Secures the refrigerator door to the cabinet and provides a stable pivot point. Replace if cracked, broken, or causing door misalignment or sagging.

A replacement cover hinge that supports and secures an appliance access cover so it opens and closes smoothly. Restores proper cover alignment and helps prevent sagging or unexpected movement for safer operation. What it does:

• Provides a pivot point for the appliance cover, allowing controlled opening and closing.
• Restores proper cover alignment to stop binding, rubbing, or uneven gaps.
• Eliminates rattling or looseness caused by a worn or broken hinge.
• Helps prevent the cover from falling open or closing unexpectedly.

• Disconnect power before inspecting or replacing any cover or access panel.
• Basic hand tools (screwdriver or nut driver) typically required; retain original fasteners.
• Reinstall in the original orientation and verify smooth operation before returning the appliance to service.
• If hinge mounting points are damaged, repair or replace mounting hardware to ensure safe installation.

Bottom door hinge for side-by-side refrigerators. Replaces worn, cracked, or broken hinges causing door misalignment or sagging. Direct fit.

Fresh food inlet cover for side-by-side refrigerators. Replaces cracked, broken, or missing covers that protect the air inlet opening.

Refrigerator freezing food? A faulty damper assembly causes constant cold air flow to the fresh food section. DIY-friendly repair, under 1 hour.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Fix interior lights that won't turn on, stay on constantly, or delay when opening the door. This switch replacement takes 10-15 minutes with basic tools.

Air separator divider for side-by-side refrigerators. Replaces cracked, broken, or missing air flow dividers in the fresh food compartment.

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.

Replaces the water filter housing manifold that delivers filtered water to your dispenser. Replace if water flow is weak, noisy, or leaking. Confirm fit.

Stores and chills water inside your refrigerator before dispensing. Replace if cracked, leaking, or damaged to restore proper water storage function.

Foam sleeve that insulates refrigerator tubing to reduce condensation. Replace when worn, cracked, or missing to restore padding and protection.

Plastic tube that connects the water tank to the dispenser and ice maker. Replace if cracked, leaking, or damaged to restore proper water flow in your fridge.

Foam insulation wraps around your refrigerator's water reservoir. Replace if torn, crushed, missing, or compressed to prevent tank sweating and condensation.

The Fresh Food Lever Assembly is an OEM part for GE refrigerators. It plays a crucial role in the operation of the refrigerator, enabling the smooth adjustment of settings within the fresh food compartment. This lever assembly is responsible for the us

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Molded duct assembly directs cold air from freezer to fresh-food section. Replace if cracked, broken, or damaged to restore proper airflow balance.