Frigidaire Range / Cooktop / Oven Control Board

Electronic clock/timer assembly that displays the time and manages timed cooking functions. Replaces a failed control clock to restore the clock readout, countdown timer and delay-start/timed-cook features. What it does:

• Displays current time and provides minute-timer/countdown functions used for timed cooking.
• Enables delay-start and timed-cook features when paired with the oven control.
• Common symptoms it fixes: blank or flickering display, clock not keeping time, timer not counting down, or unresponsive timer buttons.

• Disconnect power at the breaker before servicing to avoid shock.
• Access typically requires removing the control panel; handle the display lens and PCB carefully.
• Disconnect and reconnect the wiring harness by matching connector shapes; secure mounting screws before restoring power.
• After installation, set the clock and test timer/delay-start functions.

This clock timer is the oven's electronic control. It powers and times the bake/broil circuits and provides the display and keypad interface. Replacing a failed control can restore reliable oven operation, programming, and accurate clock/timer functions.

• Controls bake and broil relays based on user settings and oven sensor feedback
• Displays time, temperature, and status; accepts keypad commands
• Manages timed functions such as kitchen timer and delay start
• Common symptoms: blank or erratic display, unresponsive buttons, oven won't heat/start, frequent beeping or error codes

• Disconnect power at the breaker before servicing to prevent electrical shock
• Handle the board carefully and avoid static discharge; do not touch components or contacts
• Label or photograph wire connections; transfer connectors one at a time to the new control
• After installation, set the clock and test all oven functions; perform calibration if your model supports it

This mechanical timer replaces a failed or unresponsive oven/range timer to restore manual timing and cycle control. It provides a straightforward replacement for units that no longer count down or trigger timed operations. What it does:

• Advances and displays the set time so timed cooking cycles can run and finish as expected
• Starts or stops oven/range operations tied to the mechanical timer mechanism
• Replaces a timer that won't count down, won't stay set, or has a stuck/loose control shaft
• Restores manual countdown/alert functions used for timed cooking

• Disconnect power to the appliance before beginning any repair
• Label and photograph wire locations before removing leads; reinstall wires to the same terminals
• Align the timer shaft and mounting tabs carefully; do not force the shaft or overtighten fasteners

This is the main electronic control board that manages a refrigerator's key functions and timing. Replacing a failed control board restores reliable control of cooling cycles and user interface responses. What it does:

• Serves as the refrigerator's primary control center, sending and receiving signals to compressors, fans, defrost heaters, and sensors
• Can stop or correct intermittent cooling, erratic temperature behavior, or unresponsive controls when the board has failed
• Helps coordinate defrost cycles and timed operations to maintain proper temperature control
• Works with door, temperature, and system sensors to execute commanded functions

• One main electronic control board

• Disconnect power before starting—risk of electric shock if power is live
• Handle the board by its edges and avoid touching contacts to prevent ESD damage
• Verify connectors are fully seated and routed without pinching before reassembly

This is a range control panel. The control panel is the part that contains the controls for the appliance. The control panel may be needed if none of the electric range controls are working. The symptoms could vary from burners not working, the timer malfunctioning, or the display may even be blank. Inspect the part for any signs of burning or broken wires to verify that it needs to be replaced. Replacing this part is an easy process that can be done within 15 minutes. Make sure to unplug the electric range from its power source before replacing this part. The electric range control panel is sold individually. It comes straight from the manufacturer. This specific control panel is compatible with electric ranges that are manufactured by the Frigidaire brand.

A replacement electronic clock and timer assembly that restores timed cooking, clock display and audible alerts for affected ovens. Helps return normal oven scheduling and countdown functions when the original timer/control fails. What it does:

• Replaces the oven clock/timer control that manages time display, timed bake/clean cycles and end-of-cook alerts.
• Common symptoms: no clock display, timer not advancing, timed cooking won't start or stop, or intermittent control/display behavior.
• Interfaces with the oven's control system to enable countdown timers, delay-starts and audible beeps for finished cycles.

• Always disconnect power at the breaker before starting any repair to avoid shock or injury.
• Handle the display and connector ribbons carefully; avoid pulling on wires or bending contacts.
• Verify connector fit and orientation before restoring power; recheck all wiring against the appliance wiring diagram.

Main electronic control board that manages the refrigerator's control functions and user interface, helping regulate cooling, defrost, fans, and lights. Replacing a failing board restores control when the unit has unresponsive controls or erratic cycles. What it does:

• Routes power and control signals to compressor, evaporator/condenser fans, defrost heater, lights and other system components.
• Interprets user inputs and runs timed cycles; failure can cause unresponsive buttons, blank or incorrect display, or loss of user control.
• Faulty boards may lead to no cooling, continuous run, frequent cycling, or failed defrost cycles.
• Does not include sensors or wiring harnesses unless explicitly listed for this PN.

• Disconnect power (unplug or shut off breaker) before accessing or removing the old board.
• Handle the board carefully and avoid touching component leads; use anti-static precautions if available.
• Keep all mounting hardware and note connector positions to ensure correct reassembly.

Electronic control restores digital control of refrigerator settings by receiving inputs and sending signals to temperature and system components. Replaces an unresponsive or malfunctioning control board to help restore predictable user control and operation. What it does:

• Interprets user inputs and sensor signals to manage compressor, fans, defrost cycles, and lighting control
• Regulates timing and on/off control for cooling and defrost functions
• Commonly replaced when controls are unresponsive, display is blank or erratic, or cooling cycles behave inconsistently
• Used to correct intermittent or failed electronic control behavior tied to user-interface and system timing

• Disconnect power to the appliance before beginning any service
• Handle the board as a static-sensitive electronic component; avoid rough handling and contact with terminals
• Installation typically requires removing interior panels and unplugging the wire harness; retain fasteners for reassembly

This is the electronic clock/timer that controls the oven's timekeeping, display, and cooking functions. A failing control can stop bake or broil from working and make the display or keypad unresponsive.

• Governs oven functions such as bake/broil through internal relays
• Provides the time display, kitchen timer, and programmable settings
• Faulty unit can cause no heat, dead or dim display, unresponsive buttons, or error codes
• Intermittent beeping or failure to start/stop cycles can also indicate a bad control

• Disconnect power at the breaker before servicing—high voltage present
• Take a photo of wire locations; transfer connectors one at a time to the new control
• Handle the board carefully and avoid static discharge; do not touch relay contacts
• After installation, restore power and set the clock before testing oven functions

Electronic clock timer that replaces the oven's front-console clock and timer functions, restoring accurate time display and timed cooking features. Fits common Frigidaire ranges and wall ovens that use a standalone clock/timer assembly. What it does:

• Provides the oven clock display and the user timer/countdown functions.
• Enables timed cook and delay-start operations that rely on the clock/timer.
• Replaces a blank, flickering, or garbled clock display.
• Fixes unresponsive clock/timer buttons or timers that won't count down.

• Disconnect power (unplug or shut off breaker) before servicing the control panel.
• Access typically requires removing the console/control panel and unplugging a wire harness; keep fasteners/trim organized.
• Handle the assembly carefully to avoid static or physical damage to the display and connectors.

This clock timer control assembly operates the oven/refrigerator clock and timer functions so you can set cook times, delay starts, and use timed features reliably. It replaces a faulty timer/control module to restore timed cooking and display functions. What it does:

• Displays and maintains oven/refrigerator time and countdown timer
• Allows setting cook/delay-start and timed bake functions via the control interface
• Restores unresponsive or blank timer/clock displays when the control has failed
• Helps correct issues where timed functions prevent the appliance from starting

• Always disconnect power to the appliance before servicing to avoid shock
• Basic hand tools are typically required; remove control panel trim to access the module
• Handle the control and display lens carefully to avoid scratching or damaging buttons
• Verify wiring harness connectors match before final assembly; do not force connectors

This main electronic control board manages the appliance's key functions and user commands, restoring normal operation when the original board fails. It replaces a malfunctioning main PCB to fix control and response issues. What it does:

• Receives inputs from buttons/knobs and runs the appliance's control logic
• Switches power to motors, valves, heaters, and other components as commanded
• Helps regulate cycles, timing, and display/status feedback
• Commonly replaces a board that causes unresponsive controls, error codes, or erratic operation

• Disconnect power before starting—this is an electrical component
• Handle the board by its edges and avoid static discharge; use anti-static precautions
• Verify connectors and orientation match before reconnecting
• After installation, restore power and run a test cycle to ensure proper operation

The Convection Relay Board is an OEM part for Frigidaire ranges. As a specialized electronic component, it seamlessly powers the convection fan and heating elements facilitating enhanced bake modes.

Prolonged electromagnetic interference exposure from convection fan motors degrades functionality over time reducing useful life without replacement. Versatile air circulation cooking depends on consistent control response.

Causes relate to normal electromagnetic component fatigue from field induction multiplying across years of regular convection cooking cycles. Impacts introduce risks abruptly limiting advanced airflow recipes. 

Symptoms indicating relay board issues involve:

• Fan failing to start or run continuously as needed
• Inability to sync convection modes with lower/upper element operation
• Error codes and non-responsiveness during convection preheat 

Replacing with this OEM Frigidaire part restores air movement management. Compatibility also fits some Electrolux, Gibson, and Kenmore ranges.

This electronic clock timer controls the oven clock and timed cooking functions so you can set start/stop times and monitor remaining cook time. Replaces a failed or non-responsive oven/display clock to restore timed cooking features. What it does:

• Provides the oven clock display and enables timed bake/clean functions
• Starts and stops timed cooking cycles when timer/program is set
• Restores display when the clock is blank, not keeping time, or the timer won't respond
• Works with the range/oven control board to manage scheduled cook cycles

• Disconnect power to the appliance before servicing to avoid shock
• Remove the control panel trim to access and replace the clock module
• Handle the replacement part carefully and reconnect all wiring harnesses securely
• Test the oven clock/timer operation before reassembling the control panel

This electronic controller is the main control board that manages the appliance's cycles, settings and user commands for reliable operation. Replaces a failed board to restore electronic control and display response. What it does:

• Interprets user inputs and runs programmed cycles and functions.
• Powers and coordinates sensors, timers and actuators.
• Restores normal display, button/knob responsiveness and cycle selection.
• Commonly used when the appliance won't start, displays errors, or behaves unpredictably.

• Disconnect power before starting any repair to avoid shock or damage.
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available.
• Follow OEM service instructions for access and proper connector seating.