Frigidaire Range / Cooktop / Oven Parts

The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt

Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.

Symptoms of a bad Surface Element include:

• Not heating up, indicating it may be burnt out or disconnected.
• Heating irregularly or only partially, suggesting there might be damage to the element.
• Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electric heating element restores consistent, reliable heat in your appliance, so cooking or warming functions work as intended. Replace a failed element to eliminate slow heat-up, uneven temperatures, or no-heat conditions.

• Converts electrical power into heat for the appliance's designated cavity or surface
• Common failure symptoms: no heat, uneven heating, very slow preheat/warm-up
• Visual clues: breaks, blisters, or hot spots on the coil
• May cause the unit to cycle erratically or trip a breaker if shorted

• Disconnect power at the breaker or unplug before servicing; allow all components to cool
• Wear cut-resistant gloves; avoid bending or kinking the element
• Photograph wiring and transfer connectors one-for-one; ensure tight, clean terminal fits
• Inspect wires/terminals for heat damage and replace any compromised connectors

This is an oven bake igniter that mounts inside the oven compartment near the bake burner. It draws electrical current to heat up and open the gas valve, allowing the bake burner to light. Replace this part if your oven takes a long time to heat up, doesn't reach the set temperature, or fails to ignite at all.

Broiler not heating or element burned out? Replace this top broil element to restore radiant heat. Easy DIY fix with basic tools in 30 minutes or less.

This is an electronic oven control board for a gas range that manages oven temperature, bake and broil functions, and timing operations. It receives input from the temperature sensor and user controls to regulate the oven's heating cycles. Replace this board if the oven displays error codes, won't heat to the correct temperature, has unresponsive buttons, or fails to turn on altogether.

This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.

• Routes gas from the valve through the orifice to the burner head
• Positions the ignitor for reliable sparking and quick ignition
• Helps maintain correct flame size and pattern on that burner
• Common symptoms: burner won't light, clicks without flame, delayed ignition, weak or uneven flame

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; lift the cooktop to access the assemblies
• Note wire routing and original orifice location; transfer any reusable hardware from the old part
• After installation, restore gas and check connections for leaks, then test spark and flame

Dishwasher door seal prevents leaks by creating a watertight barrier around the door. Replace if you notice water pooling or leaking. Verify fit with your model.

Fix F10 error codes, blank displays, or temperature fluctuations. This oven control board restores bake/broil cycles and keypad response in your range.

Burner orifice regulates gas flow to your range burners. Replace if clogged with debris, corroded, or damaged to restore proper combustion and heat output.

Element not heating? This surface element is the most common fix. Compatible with Frigidaire electric ranges. Tests between 15-45 ohms resistance.

Burner cap sits on top of the gas burner assembly to distribute flame evenly. Replace if cracked, chipped, discolored, or missing for proper cooking.

Frames your range's ventilation opening. Replace if cracked, discolored, or missing. Installs around vent area for a finished appearance.

Oven won't heat or shuts off during use? A blown thermal fuse cuts power to prevent overheating. Simple diagnosis with a multimeter, quick replacement.

Replaces cracked, broken, or missing trim on your range door. Restores a finished look, holds glass in place, and eliminates gaps around the door edge.

Adhesive overlay that restores faded or damaged button labels on your oven control panel. Replaces worn, bubbled, or peeling faceplates.

Range not heating or display blank? The main control board coordinates all cooking functions. This electronic repair requires basic skills and 30-45 minutes.