Frigidaire Range / Cooktop / Oven Parts

Replace cracked or broken oven door glass on your gas range. This tempered glass panel installs in the door frame, restoring visibility and appearance.

This is the middle glass panel that sits between the inner and outer glass layers of the oven door assembly. It serves as part of the insulation system, helping to retain heat inside the oven and keep the outer door surface cool. Replace this panel if it is cracked, chipped, or shattered, which can lead to heat loss and excessive outer door temperatures.

This component creates the spark to ignite gas burners and includes the gas orifice for proper fuel delivery, located beneath each surface burner. Replace if the burner won't light, takes excessive time to ignite, or produces an irregular flame pattern.

Replaces cracked or broken oven door glass on electric ranges. Covers the inner cavity and allows viewing without opening the door. Essential when damaged.

Control knob for electric range stovetop elements. Mounts to the front control panel. Replace if cracked, broken, or markings are worn and illegible.

Burner won't light or clicks continuously? This gas cooktop igniter creates the spark to ignite your burner. Simple fix in under 30 minutes.

This is the large surface heating unit for an electric range or cooktop. Replacing a failing unit restores consistent stovetop heat so cookware warms predictably and meals cook evenly.

• Provides the heat source for the large burner position on an electric cooktop
• Converts electrical energy into controlled cooking heat
• Replace if the burner won't heat, heats intermittently or unevenly, or shows visible breaks, blistering, or burn spots
• Loose, pitted, or discolored terminals can also indicate the unit is failing

• Disconnect power to the appliance before servicing and allow all components to cool completely
• If your model uses plug-in coils: lift slightly and pull the old unit straight out of the receptacle; align and push the new unit straight in until fully seated
• Inspect the burner receptacle for heat damage before reassembly
• Restore power and test operation on low and high settings

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

Securely attaches the oven door to the range cabinet. Replace if your hinge is cracked, bent, worn, or causing the door to hang unevenly or not close properly.

Regulates gas flow and pressure to your cooktop burners. Replace if damaged, worn, or if gas won't flow properly through the regulator assembly.

Replacement cooktop grate for gas ranges. Sits above the burner to securely support pots and pans. Ideal for replacing cracked, broken, or worn grates.

Insulation blanket surrounds the oven cavity to retain heat. Replace if burnt, deteriorated, or damaged by pests to restore proper heat retention.

Replacement touch pad overlay for range control panels. Restores clear button labels and refreshes appearance when original is cracked, peeling, or worn.

Adhesive control panel overlay that restores faded, peeling, or bubbled button labels on your range. Replace when graphics become unreadable or worn.

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

Burner won't heat or stays on constantly? This range burner control switch regulates cooktop element temperature. Straightforward DIY fix.