Frigidaire Range / Cooktop / Oven Parts

Range won't turn off or functions stay powered on? This relay board controls electrical flow to range components. Common fix for stuck-on appliances.

This is a black burner cap that sits on top of a small surface burner on a gas range. It distributes the flame evenly around the burner for consistent heating. Replace this cap if it is chipped, cracked, warped, or if you notice uneven or yellow flames on the small burner.

Replaces a damaged, cracked, or missing bottom drawer on your range. Restores smooth slide action and a flush, finished look to the storage compartment.

Restores proper door alignment and smooth operation when hinges are worn, bent, or binding. Replaces damaged hinges to help door sit flush and close correctly.

This insulation panel fits inside the refrigerator cabinet to help maintain interior temperatures and reduce heat transfer to the outer shell, supporting more consistent cooling and helping limit frost buildup. What it does:

• Forms a thermal barrier between the interior liner and outer cabinet to help hold cold air inside.
• Helps reduce frost and moisture buildup around the liner when intact.
• Worn, torn, or missing insulation can contribute to longer run times, uneven cooling, or more frequent defrost cycles.
• Replaces damaged insulation to restore proper temperature retention and improve appliance efficiency.

• Always disconnect power to the appliance before starting any repair.
• Panel may be secured with clips, adhesive, or foam sealant; remove and install carefully to avoid damaging the liner.
• Inspect surrounding seals, gaskets, and fasteners while accessing the cavity; replace any damaged components.

Insulation blanket surrounds the oven cavity to retain heat. Replace if burnt, deteriorated, or damaged by pests to restore proper heat retention.

Replace a cracked, clogged, or damaged ignitor orifice assembly under your gas range cooktop. Routes gas to surface burner and houses spark electrode.

The Knob is an OEM part for Frigidaire ranges. This component allows users to control the heat levels of the burners or the oven by turning the corresponding control shaft. It ensures precise adjustments for cooking and baking.

Over time, the knob can wear out or break due to frequent use, exposure to heat, or accidental impacts. Causes of a bad knob include cracking, stripping of the internal connection, or the knob becoming loose and difficult to turn.

Symptoms of a bad knob include:

• Difficulty in turning the knob
• Inconsistent or unresponsive heat adjustments
• The knob becoming loose or falling off
• Visible cracks or damage to the knob

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement control knob for range burner and oven settings. Installs on the control shaft. Needed when original knob is worn, broken, or missing.

Fixes loud noises or no airflow from convection fan. This motor drives the fan to circulate air evenly during cooking. DIY-friendly repair in 10-30 minutes.

Restores printed labels and icons on your range's electronic control panel. Replace when overlay is worn, peeling, faded, or cracked for easy-to-read settings.

Fix F10 errors, inaccurate temps, or unresponsive heating with this oven control board. Restores bake/broil functions and clock display. Moderate DIY.

Burner grate for gas ranges and cooktops. Supports cookware over the burner flame. Replace if warped, bent, rusted, chipped, or broken for safe cooking.

Right side oven door hinge for your range. Replaces broken, bent, or worn hinges that prevent proper door closure. Installs on range frame. Sold individually.

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation