Frigidaire Range / Cooktop / Oven Parts

This rocker switch is the on/off control used in the appliance's control panel. It opens and closes the circuit to a selected feature, restoring dependable operation when the original switch becomes worn, stuck, or fails.

• Controls a single on/off circuit from the control panel
• Restores proper switching for the associated feature
• Common symptoms: feature won't turn on or off, light or function flickers or stays on, switch feels loose or sticks
• Replaces a cracked, burned, or unresponsive rocker

• Disconnect power at the breaker before servicing
• Access the switch from the control panel or mounting area; note/photograph wire positions
• Move wires to the new switch one at a time and seat the switch securely in the panel opening
• Restore power and test operation before reassembly

This clear glass shelf provides a sturdy, easy-to-clean storage surface for your refrigerator, helping keep food organized and visible. It restores usable shelving space when an original shelf is cracked, chipped, or missing. What it does:

• Supports food containers, plates and small appliances so items stay organized and level.
• Prevents spills and crumbs from falling to lower compartments; makes clean-up quicker.
• Replaces cracked, chipped or broken shelves that can cause items to shift or fall.
• Restores a proper storage surface when the original interior shelf is damaged or removed.

• Remove food and any loose items from the shelf area before replacing the glass.
• Handle with care and wear cut-resistant gloves; support the glass from underneath while sliding into place.
• Inspect shelf supports or rails for damage and position the glass evenly on the supports; do not force the shelf into misaligned rails.
• Refer to your appliance's owner manual or service guide for model-specific placement instructions.

This replacement control knob lets you turn the range's control shaft to set burner or oven temperature. Swapping a cracked or loose knob restores a secure grip and accurate, easy selection of settings.

• Attaches to the control stem to adjust heat levels or oven temperature
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob falls off or spins without engaging the control
• Restores proper feel and alignment of settings on the control panel

• Ensure the appliance is off and cool before servicing
• Pull the old knob straight off the stem; do not twist or pry with tools
• Align the new knob with the stem orientation and press firmly until fully seated
• If the knob won't seat, inspect the control stem for wear or damage before forcing

This clock timer is the electronic control that runs your range or wall oven's display, timer, and cooking functions. Replacing a failed control restores the clock/timer and reliable bake/broil operation when the display or controls stop working.

• Manages the clock, timer, and user interface; processes keypad/touchpad inputs
• Controls bake and broil elements via internal relays to reach and maintain set temperatures
• Coordinates preheat and temperature regulation using sensor feedback
• Common symptoms of failure: blank or erratic display, unresponsive buttons, oven won't start or heat, or unexpected error codes

• Disconnect power at the breaker before servicing; verify no voltage at the appliance
• Photograph/label wire connections and move harnesses one at a time to the new control
• Transfer any model-specific mounting hardware or faceplate as needed
• Handle the board by the edges and protect from static discharge

6 inch, 1200 watt single radiant surface element.

This motor powers the oven's fan to move air through the cavity or chassis, depending on the model. Replacing a weak or failed motor restores proper airflow, helping maintain stable temperatures and protect internal components during cooking and cool-down. What it does and common symptoms:

• Drives the oven's fan for cooling and/or convection airflow
• Fan does not run or starts intermittently
• Loud humming, squealing, or grinding from the fan area
• Control area feels unusually hot or oven struggles to maintain temperature
• Uneven baking performance when using convection (on applicable models)

• One motor

• Disconnect power at the breaker before servicing; allow the oven to cool
• Access is typically from the rear or top; remove panels to reach the motor
• Note wire locations and any rotation markings before removal; transfer any attached fan wheel/bracket as required
• After installation, rotate the fan by hand to check for clearance, then restore power and test operation

Replacement wiring harness that connects control electronics to internal components, restoring proper electrical connections and reliable operation. Use when factory wiring is damaged, loose, or causing intermittent component failures. What it does:

• Routes power and signal between the appliance control board and internal components.
• Restores continuity when broken, frayed, or corroded wires cause intermittent or no operation.
• Can resolve symptoms such as non-responsive controls, lights or fans not running, or intermittent component operation.
• Keeps wiring neat and secured along original routing to prevent rubbing and stress.

• Always disconnect power (unplug or shut off breaker) before starting any repair.
• Match connector shapes and pin counts; route harness along original clips and pathways to avoid pinch points.
• Inspect mating connectors and terminals for damage or corrosion before reconnecting.

This control knob replaces a damaged or missing knob on your cooking appliance, restoring smooth, accurate adjustment of settings. Refresh worn controls for better usability and a clean, finished look. What it does:

• Attaches to the control shaft to select heat or function settings
• Helps resolve issues like a cracked knob, stripped insert, or a knob that falls off
• Restores smooth turning and proper alignment when adjusting settings
• Replaces a knob that won't turn or is difficult to grip

• One control knob

• Disconnect power at the breaker; ensure all controls are in the OFF position and surfaces are cool
• Pull the old knob straight off the control shaft
• Align the flat/D-shaped shaft orientation and press the new knob on firmly until seated
• Do not force; verify pointer alignment and smooth operation after installation

This factory seal creates a tight barrier between cooking appliance components to contain heat, moisture, and spills so your unit performs efficiently. Replace a worn or damaged seal to restore proper containment and performance. What it does:

• Seals joints between mating parts to prevent air leaks and liquid intrusion
• Helps maintain stable oven temperatures and efficient preheating
• Reduces escape of heat, odors, and smoke from sealed areas
• Replace if cracked, flattened, torn, or missing

• 1 seal

• Disconnect power; shut off gas supply before servicing
• Allow the appliance to cool completely
• Note the original seal's routing/orientation; remove old seal and clean mating surfaces
• Seat the new seal evenly without stretching; verify proper fit and operation after reassembly

This electronic oven control board manages oven temperature, bake/broil functions, and the display/keypad. Replacing a failed board restores proper heating and responsive controls so the oven operates and times as it should. What it does:

• Regulates power to the bake/broil elements or gas valve to reach and maintain set temperature
• Interprets keypad inputs and controls oven modes (Bake, Broil, Start/Stop, Timer)
• Drives the digital display for time, temperature, and status
• Common symptoms of failure: no display, unresponsive buttons, oven won't heat or overheats, or recurring error beeps/codes

• 1 electronic control board assembly

• Disconnect power at the breaker; turn off gas supply for gas ranges
• Use ESD precautions; handle the board by its edges
• Label and transfer wire connectors one at a time; move any mounting hardware/overlay from the original, if required
• After installation, restore power, set the clock, and test oven modes

This replacement part is a genuine OEM frigidaire oven control board. The oven control board is the main circuit board that controls the ovens' essential functions. If the oven isn't heating properly, not turning on, or showing an error code on the digital display, it might be time to replace the control board. Replacing a control board may seem like a difficult task, but it is actually a relatively simple process. First, unplug the power to the stove. Move the appliance back to gain access to the back. Remove the upper back panel, and locate the control board. Take note of the order of the wires using a phone camera. Then detach the wire harness from the old control board. Remove any individual wires with needle-nose pliers. Then re-attach the wires to the new control board in the correct terminals. Snap the new control board into place and reinstall the upper back panel of the range.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This electronic control board regulates oven functions and the display, interpreting keypad inputs and controlling the bake and broil elements. Replacing a failed board restores responsive controls, accurate heating, and a readable clock/timer.

• Controls bake and broil element power using temperature sensor feedback
• Manages oven modes, timers, and the display/clock
• Interfaces with the keypad membrane to read user selections
• Failure symptoms can include no heat, oven won't start, erratic temperatures, or a dead/flickering display

• Disconnect power at the breaker before servicing to avoid electrical shock
• Handle the board by the edges; use ESD protection to prevent static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Reuse existing mounting hardware and front overlay if applicable; correct orientation before securing

Replace the oven's lower heating element to restore reliable bake heat and more even cooking. This bake element supplies the primary lower heat during bake cycles so your oven can reach and maintain baking temperatures. What it does

• Provides the lower heating source used during bake cycles for baking and roasting
• Replaces a burned, broken, or open bake element that won't glow or heat
• Helps correct uneven baking or failure to heat on the bake setting
• Visible signs: blistering, breaks, or dark spots on the element

• Always disconnect power at the circuit breaker before servicing the oven
• Allow the oven to cool completely and wear gloves to avoid cuts from sharp edges
• Support the element while disconnecting terminal wires; secure wiring and terminal nuts when reinstalling
• Test the bake function after restoring power

Note: Quantity of two brackets

This potentiometer kit is the user-adjustment control the appliance reads to set operating levels. Replacing a worn potentiometer restores smooth, predictable response when you turn the knob, helping the control register settings accurately.

• Varies electrical resistance so the control can interpret knob position
• Helps set functions such as speed, power level, or temperature as designed
• Failure can present as no change when turning the knob, jumpy/erratic response, or settings stuck at one level
• Can also cause intermittent operation or "dead spots" while adjusting

• Disconnect power to the appliance before servicing
• Access the control area; note wire positions or take a photo before removal
• Transfer any knob/shaft adapter from the old part if applicable; secure the new pot without over-tightening
• Route wiring away from sharp edges and heat sources; verify proper operation before reassembly

This electronic oven control board governs the appliance's heating and front-panel functions. Replacing a failed board can restore accurate temperature control, mode selection, and display/timer operation.

• Controls bake and broil relays to reach and maintain the set temperature
• Manages the oven clock, timer, and digital display
• Receives keypad inputs for mode and temperature selection
• Monitors the temperature sensor and can register fault codes
• Common symptoms: oven won't heat or start, blank/erratic display, unresponsive buttons, random beeps or error codes

• Disconnect power at the breaker before servicing
• Use ESD precautions; avoid touching circuitry and contacts
• Label or photograph all wiring; transfer mounting hardware and the existing faceplate/overlay if applicable
• After installation, run a test cycle; some models may require initialization or calibration per the service sheet in the unit