Frigidaire Range / Cooktop / Oven Parts

This surface burner gas valve regulates the flow of gas to the burner on your range or cooktop, enabling proper ignition and flame control. Replacing a worn valve restores safe operation and consistent flame performance.

• Meters gas to the burner in response to the control knob
• Supports reliable ignition and maintains a stable, adjustable flame
• Typical symptoms: burner won't light, flame won't adjust or goes out, knob stiff or difficult to turn
• Can help correct uneven heat on the affected burner

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; remove panels as directed by your model's service information
• Note valve orientation; transfer any model-specific brackets or fittings from the old valve if required
• After reassembly, check all connections for leaks with a soap-and-water solution

This replacement control panel restores a clean, finished look to your appliance's console area and provides a sturdy mounting surface for the user interface. It helps protect internal components and keeps controls properly positioned. What it does:

• Forms the exterior face and mounting surface for the console/backguard area
• Shields internal wiring and components from heat, spills, and impacts
• Keeps buttons, knobs, and display openings aligned and secure
• Common symptoms: dents, cracks, broken mounting points, loose or warped panel, controls not sitting flush

• 1 control panel

• Disconnect electrical power at the breaker or unplug the appliance; shut off gas supply if applicable
• Wear cut-resistant gloves—panel edges can be sharp
• Remove console/backguard screws, then transfer any brackets or clips from the old panel to the new one
• Tighten mounting screws evenly and confirm control alignment before restoring power

Replacement clock timer control that restores the oven/range clock display and basic timed-cooking functions. Ideal for appliances with a blank or unresponsive clock that need the timer and time-of-day features working again. What it does:

• Displays the current time and runs the oven/range timer and delay-start features.
• Manages timed cooking cycles (start/stop) and basic clock functions.
• Common replacement for a blank display, unresponsive buttons, or incorrect time/timer operation.

• Always disconnect power at the circuit breaker or unplug the appliance before servicing.
• Handle the display, glass, and electrical connectors carefully; avoid bending ribbon connectors or exposing the unit to moisture.

This is the variable control switch for an electric range's cooktop burner. It regulates power to the surface element so you can select steady, repeatable heat levels and restore reliable on/off control. What it does:

• Regulates voltage to a surface element based on knob position (low through high)
• Typical failure symptoms: burner won't heat, only heats on high, won't shut off, or heats inconsistently
• Can address issues when the control shaft is damaged or the switch shows signs of overheating at the terminals

• 1 switch

• Disconnect power before servicing
• Access the control panel/console to reach the switch
• Note wire locations and transfer them to the new switch one at a time
• Secure the switch in the panel, reinstall knob, and test burner operation before reassembly

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This top burner gas valve controls and shuts off gas to a single surface burner so you can ignite and adjust flame height safely. Replace a worn valve to restore precise burner control and dependable lighting.

• Regulates gas flow to one surface burner for reliable ignition and flame adjustment
• Acts as the on/off shutoff for that burner via the control knob
• Helps when a burner won't light even though the igniter clicks
• Helps when flame won't adjust smoothly or the knob binds/feels stripped

• Disconnect power and shut off gas supply before servicing
• Remove knob and access the control/manifold area to reach the valve; note tubing and mounting orientation
• Transfer any model-specific brackets or fittings from the old valve if required
• After reassembly, check all connections with an approved gas leak-detection solution before restoring service and testing burner operation

The Handle is an OEM part for Frigidaire ranges. Crafted from durable heat-resistant metal, these handles provide safe, ergonomic access to oven interiors during cooking cycles.  

Prolonged exposure to elevated oven temperatures causes typical discoloration of painted finishes as well as looseness from load stresses reducing tactile control over years. Cooking convenience decreases without gripable surfaces.

Symptoms indicating handle wear include:

• Faded, chipped, or flaking handle finishes  
• Loose, rattling, or awkward movement from placement
• Deteriorating mounting attachments risking accidental falls

Replacing with this OEM Frigidaire handle restores tactile guidance into the cooking cavity. Compatibility also fits some Kenmore, Electrolux, and Gibson ranges renewing secure doorknob function through authorized maintenance. 

This oven door hinge controls and supports the door's movement, allowing it to open smoothly and close tightly. A secure, balanced hinge helps preserve the door seal and maintain consistent cooking temperatures.

• Supports door weight and balances spring tension for smooth opening and controlled closing
• Helps the door close fully against the gasket to reduce heat loss and temperature swings
• Replaces worn or bent hinges that cause sagging, slamming, or a door that won't stay closed
• Can reduce squeaks or binding and restore proper door alignment

• Disconnect power and allow the appliance to cool completely before servicing
• Remove the door; lock hinge clips or insert hinge pins before lifting the door off
• Note hinge orientation and spring tension when transferring; keep hands clear of moving spring arms
• After installation, verify door alignment and that the gasket contacts evenly all around

This wiring harness connects and routes power between key refrigerator components, restoring proper electrical signals so fans, lights, compressor and ice/water functions can operate correctly when the original harness is damaged. What it does:

• Provides the factory routing and connectors to link controls, motors and sensors
• Replaces frayed, burnt or broken wires that can cause intermittent power or no-power to components
• Helps resolve symptoms such as lights or dispenser not working, fans not running, or ice maker/pump failures when wiring is the cause
• Maintains factory-style connector fit and wire lengths for correct component connections

• Disconnect power to the appliance before inspecting or replacing the harness
• Match the part number and connector shapes to the original; route and secure wires per factory clips to avoid heat or pinching
• If connectors are corroded or terminals are damaged, replace the harness rather than attempting temporary repairs

This ignitor harness connects the oven ignitor to the range's wiring, restoring a secure electrical path for reliable ignition. Replacing a damaged harness can help get your gas oven lighting and heating properly again. What it does:

• Transfers power from the oven wiring to the ignitor so the burner can light.
• Replaces frayed, burned or broken wires that can cause intermittent ignition or no ignition at all.
• Improves connection integrity to reduce sparking or loose-contact symptoms.
• Common symptoms this part can address: oven won't light, bake/broil doesn't heat, or ignitor fails to glow.

• Turn off electrical power and gas supply before starting any work; ensure the appliance is cool.
• Remove access panels and disconnect old harness at terminals; compare connectors before installing the new harness.
• Make secure, tight connections and route the harness away from sharp edges and high-heat surfaces.

This genuine OEM part is a clock timer for ovens. The clock timer is the part of the oven that allows the user to set a time for cooking and baking. If the timer buttons are no longer responding to touch or the timer's digital display is no longer visible, it will need to be replaced. Luckily, replacing a timer is a fairly simple repair.To get started, make sure the range is unplugged. Once unplugged, pull the range out and away from the wall to gain access to the upper back panel. Remove the mounting screws to the panel to gain access to the back of the control panel. Locate the timer and proceed to unthread the screws that hold it in place. Once loosened, pull the timer out of its place and install the new timer by threading the mounting screws that secure it to the control panel. Reinstall the upper back panel and restore power to the appliance.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This convection fan motor turns the oven's rear fan to circulate hot air during convection bake and roast. Replacing a failing motor restores even heat distribution and reliable convection performance.

• Drives the convection fan to move hot air throughout the oven cavity
• Helps maintain uniform temperature for faster, more even results
• Symptoms include the fan not running or intermittent operation in convection mode
• Can contribute to uneven baking or extended preheat times during convection cycles

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely before beginning work
• Access point varies by model
• Note wire locations and fan blade orientation during removal; wear cut-resistant gloves due to sharp edges

The Supply Tube is an OEM part for Frigidaire gas ranges. It is a flexible metal tube that safely transports natural gas fuel from the household supply line to each burner assembly on the cooktop. 

Symptoms of a bad supply tube include: 

• Gas leaks at connections or along tube seams
• Inconsistent or weak burner flame levels
• Burners that light unevenly or not at all

Causes of failure can be cracking/corrosion of older tubing from regular heating/cooling cycles, damage from stove movement, or accidental kinks that reduce gas flow. 

Replace with this genuine Frigidaire supply tube to ensure a reliable source of fuel for each burner. It is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges, providing years of dependable cooking performance. 

The Burner Grate is an OEM part for Frigidaire gas ranges. It supports racks and pans directly over the range's gas burners during cooking. The burner grate must withstand constant exposure to high heats without warping or degradation.

Causes of a bad burner grate include wear from heavy use over multiple years, corrosion from spills or food particles left on the grate, or cracks and chips that compromise durability and function.  

Symptoms of a bad burner grate are:

• Uneven or inefficient heat transfer to pots and pans during cooking  
• Warping or distortion of grate bars impacting pan support
• Sharp edges or breakage causing potential safety hazards

This OEM replacement grate is also compatible with some Electrolux, Crosley, and Amana gas ranges. 

This surface burner grate supports cookware on your gas cooktop, keeping pots and pans stable above the flame. Replace a cracked or warped grate to restore safe pan support and consistent burner performance.

• Holds cookware at the proper height above the burner flame
• Provides a stable, level surface for pots and pans
• Replace if cracked, warped, or missing to prevent wobbling or tipping
• Common symptoms include unstable cookware, uneven heating, or visible damage to the grate

• Turn all burners off and allow the cooktop to cool completely before handling
• Lift off the old grate and clean the area if needed
• Position the new grate so its feet sit flat and openings align with burner caps
• Test with a pan to confirm it sits level and stable

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance