Frigidaire Range / Cooktop / Oven Parts

Replacement control knob for your range. Attaches to the control shaft to operate burners or oven functions. Replace if cracked, broken, or missing.

Replacement oven burner that restores heat in the oven's bake chamber so you can cook evenly. Installs in place of a damaged or worn burner to help the oven reach and maintain proper cooking temperatures. What it does:

• Produces the primary bake heat for the oven cavity.
• Replaces a cracked, corroded, or non-functioning burner that may cause weak or no heat.
• Helps correct uneven baking or failure to reach set temperatures when the burner is the source of the problem.

• Disconnect electrical power and shut off the gas supply before beginning work; follow all local codes.
• Use appropriate hand tools and avoid forcing parts; inspect sealing surfaces and connections for damage.
• If gas fittings or ignitors are involved, test for leaks after installation.

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

Replace a broken, cracked, or missing control knob on your electric cooktop. Installs on the control panel to adjust burner settings and temperature.

Snap-on burner cap for gas cooktops and ranges. Restores finished appearance and protects components. Replace if cracked, chipped, or missing.

If your oven won't heat, the broiler stays on constantly, or timed cooking cycles fail, this mechanical timer restores manual timing and cycle control.

Size: 8 inch. 2200 watt. Radiant.

Convection fan motor that circulates hot air inside the oven cavity for even cooking temperatures. Replace if fan stops spinning or makes excessive noise during convection baking.

Secures spray arm assembly components in your dishwasher. Replace if screw is stripped, loose, missing, or broken to keep the spray arm properly mounted.

This gas supply tube routes fuel from the valve/manifold to a burner in your gas cooking appliance. A sound tube helps deliver a steady flame and safer, reliable operation by maintaining a sealed path to the burner.

• Directs gas from the control valve/regulator to the designated burner
• Maintains a sealed pathway to help prevent leaks
• Supports proper ignition and consistent flame size on the affected burner
• Common signs of a problem: gas odor near the tube, visible kinks/corrosion, hissing, or weak/no flame

• Disconnect power and shut off the gas supply; allow the appliance to cool
• Work in a well-ventilated area; support fittings with two wrenches to avoid stressing the valve/manifold
• Route the new tube exactly like the original; start threads by hand and tighten securely without over-torquing
• After reassembly, restore gas and check all joints with an approved leak-detection solution.

Control panel not responding or oven won't heat? This electronic control board manages all oven functions. Moderate difficulty repair requiring basic wiring.

Range won't heat or shows F10/F11 error? This electronic control board manages oven temperature and timed cooking. Moderate DIY repair, 30-45 minutes.

Burner won't heat or stays on constantly? This infinite switch restores variable heat control to your cooktop element. Moderate DIY repair.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Burner won't light or flame height won't adjust? This top burner valve controls gas flow to restore reliable ignition and precise flame control.

Replacement refrigerator door hinge that supports proper door alignment and smooth opening and closing. Restores secure door operation to prevent sagging, binding or air leaks when a hinge is worn or damaged.

• Supports and pivots the refrigerator door for stable, reliable opening and closing.
• Maintains door alignment to reduce gaps that can cause cold air loss and temperature issues.
• Designed to match factory fit and function for the door hinge mechanism.

• Disconnect power and remove food from the door before starting to reduce risk of injury or damage.
• Support the door while removing and installing the hinge to prevent it from falling or bending.
• Retain original mounting hardware; use the correct screws and torque values per the service manual.