Parts for Crosley CDG7500KW0: Front Panel / Lint Filter Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replaces cracked or damaged dryer grill trim to restore appearance and proper airflow direction. Check your model number for exact fit confirmation.

White plastic plug insert that covers unused openings on your dryer. Keeps out dust and debris while restoring a clean finish. Replace if cracked or missing.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replace your dryer's front panel if it's cracked, dented, or damaged. This panel forms the exterior front surface of your dryer cabinet housing.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

The Door Switch is an OEM part for Frigidaire dryers. This part ensures that the dryer operates safely by only allowing the machine to run when the door is completely closed. Positioned typically at the door frame, the switch activates when the door is shut, signaling the control system that it's safe to begin the cycle.

Over time, door switches can wear out or become damaged, which can interfere with the normal operation of the dryer. 

Symptoms of a faulty Door Switch include:

• The dryer not starting when the door is closed.
• The dryer stopping unexpectedly, which might be due to a loose or faulty switch.
• A lack of the usual "click" sound that indicates the door has latched properly, suggesting the switch isn’t engaging.
• The dryer continuing to run when the door is opened, which poses a significant safety risk.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Traps lint and debris during drying. Replace when mesh appears clogged, melted, or reduces airflow. Confirm fit with your model number before ordering.

Secures hose connections in dryers to prevent leaks and maintain proper airflow. Replace if hoses are loose or disconnected. Verify fit with model.

Replacement door hinge for dryers. Installs on the door opening to enable proper opening and closing. Needed when hinge is cracked, broken, or worn.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Dryer control panel that houses the interface and display. Replaces cracked, damaged, or discolored panels to restore the appearance of your appliance.

Replace your dryer door gasket to restore an airtight seal and prevent heat loss. Installs in minutes—just pull out the old, snap in the new. Confirm fit.

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Plastic door cover

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

Fastens panels, brackets, and internal components in your dryer. Replace stripped, rusted, or missing screws to restore secure mounting and alignment.

Replace your dryer's heater plug insert if it's cracked, broken, or missing. This small component fits into the heater housing to secure connections.

T-plug electrical connector for dryer wiring harnesses. Replaces damaged, corroded, or broken plugs to restore secure connections between components.

Replacement plug insert for dryer control panels and housing assemblies. Needed when original plug is cracked, broken, or missing from dryer cabinet.

Sound dampening pad for dryers. Installs inside the cabinet to reduce vibration and noise. Replace if worn, torn, or missing for quieter operation.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.