Gaggenau Parts

This is a foam sealing strip that creates an airtight seal between panels or the door area of the microwave. It helps prevent heat loss, air leaks, and moisture intrusion. Replace this strip if it appears compressed, crumbling, or if you notice gaps, rattling noises, or reduced heating efficiency.

This is a rubber or silicone sealing grommet used to create an airtight seal around openings or connections within the microwave. It helps prevent moisture, heat, and air from escaping or entering where components pass through panels. Replace this part if you notice steam leaking from unusual spots, rattling noises near sealed areas, or visible cracking and deterioration of the original seal.

Replacement silverware basket holds and organizes forks, knives, and spoons in your dishwasher. Replaces cracked, broken, or missing cutlery holders.

This door latch assembly secures the door closed and signals the control that it's safely shut, allowing cycles to start and run. Replacing a worn latch restores a reliable safety interlock and consistent operation.

• Secures the door and engages the safety interlock so the appliance can operate
• Sends a "door closed" signal to the control
• Common symptoms: door won't latch or stay closed; unit won't start or pauses as if the door is open; intermittent operation when the door is bumped; visible wear or damage to the latch
• Helps prevent nuisance "door open" indications

• Disconnect power before servicing
• Access the latch from the door area; remove inner panel or trim as required by your model
• Note wire positions, transfer connectors, and mount the new latch in the same orientation
• Test door closure before reassembly

Mounting screw for refrigerator assembly. Secures components and panels in place. Replace if screw is stripped, missing, or no longer holding tight.

This grease filter captures airborne grease from oven ventilation to help reduce buildup and keep internal parts cleaner. It fits flush in the oven vent and is a replaceable maintenance part. What it does:

• Traps cooking grease and airborne oils before they reach fan and ducting
• Helps reduce grease deposits that can cause smoke or odors during cooking
• Supports proper airflow by preventing clogging of the vent path
• Visible grease or darkened filter surface are common signs it needs replacement

• Disconnect power to the appliance before removing or installing the filter
• Slide or snap the filter into the vent slot per the appliance's filter-retention method
• Handle carefully to avoid sharp sheet-metal edges; wear gloves if needed
• Clean surrounding area and check the vent for heavy buildup when replacing

Seals the heating element opening to maintain proper heat and prevent leaks. Replace when worn or damaged to restore efficient operation. Confirm fit.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Restore smooth, controlled door movement and a tight oven seal with this door hinge. Replacing a worn hinge helps the door close fully, prevents heat loss, and brings back the original opening tension on top or bottom compartments.

• Controls door swing and spring tension for smooth opening/closing
• Maintains alignment so the door gasket seals evenly
• Helps the door stay closed during cooking and hold at designed positions
• Common symptoms: door won't close fully, drops/sags, uneven gap, squeaks/binds, or heat escaping

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door; support it to safely relieve hinge spring tension
• Note hinge orientation and attachment points; transfer and secure the hinge using existing mounting locations
• After reassembly, verify latch engagement and even gasket contact; many ovens use two hinges—replace in pairs if both show wear

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.