General Electric Microwave Screws, Nuts, Washers

This tapping pan-head screw secures interior panels and components in appliances, providing a low-profile head and threads that form into metal for a firm hold. It's a direct-fit fastener for repairs and replacements. What it does

• Fastens panels, brackets and small appliance components where a self-tapping screw is required
• Pan-head profile gives a flush, low-profile finish that resists snagging
• Threads cut into mating metal to create a secure attachment without a nut
• Commonly used where sheet-metal or thin-frame fastening is needed

• One tapping pan-head screw

• Use the correct screwdriver bit that matches the screw recess to avoid stripping
• Start in a pilot hole or with light initial pressure to ensure proper thread formation
• Tighten until snug; do not over-torque — overtightening can strip threads or deform panels
• Wear eye protection when working with metal fasteners and sheet metal

This is a small replacement screw used to secure appliance panels and components, restoring proper fit and preventing loose parts. It's a direct-fit fastener commonly used in various GE appliance assemblies. What it does

• Secures trim, panels, brackets or control components to prevent movement and rattling.
• Replaces missing, stripped, or corroded screws that can allow gaps or vibration.
• Helps restore proper alignment of parts that can cause noise or loose-feeling doors/panels.

• Use the matching screw hole and thread; do not force or cross-thread the screw.
• Hand-start the screw, then tighten with the correct screwdriver to a snug fit—avoid over-tightening.
• Disconnect power before working near electrical components; follow appliance safety procedures.

This is a replacement mounting screw used to secure panels and components on compatible appliances. It restores proper fit and prevents rattling or loose parts for a safe, stable appliance. What it does:

• Secures panels, trim, brackets or small components in place
• Replaces missing or stripped fasteners that cause rattling or loose parts
• Helps maintain appliance alignment and safe operation when installed properly
• Small fastener for interior or exterior appliance assemblies

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct screwdriver and hand-start threads to avoid cross-threading
• Do not overtighten; snug until secure to prevent stripping or damaging parts

This is a binding-head screw used to fasten panels and components on compatible GE appliances. It provides secure, low-profile fastening where a binding head design is required for proper fit and alignment. What it does

• Secures panels, brackets, or small assemblies to prevent movement or rattling.
• Replaces a missing or stripped screw that causes loose parts or squeaks.
• Restores proper alignment for components that rely on the binding-head profile.
• Works where a shallow, rounded head and threaded shaft are specified.

• Use the correct driver size to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or damaging parts.
• Disconnect power and follow all appliance-specific safety procedures before accessing panels.

Includes 12 screws.

This handle tapping screw secures an appliance's handle to its door or front panel. Replacing a missing or stripped screw restores a firm, safe grip and prevents a loose or rattling handle. What it does:

• Fastens the handle to the door or front panel
• Self-tapping design engages/cuts threads for a secure hold
• Replaces missing, rusted, or stripped handle screws
• Helps correct a loose, wobbly, or rattling handle

• One handle tapping screw

• Disconnect power before service; for gas ranges, also shut off gas
• Support the handle while removing/installing screws to avoid stressing glass or trim
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Keep track of any decorative end caps or spacers for reassembly

This installation hardware kit provides the mounting fasteners and brackets needed to secure the appliance during installation for a stable, code-compliant fit. Use it to complete new installs or replace missing hardware. What it does:

• Provides the mounting fasteners and brackets used to secure the appliance to surrounding cabinetry or floor
• Prevents shifting, tilting or excessive vibration after installation
• Enables proper alignment and stable operation following service or replacement
• Restores missing or damaged installation hardware so the appliance installs correctly

• Follow the appliance installation instructions and local codes; use only the fasteners supplied or specified by the manufacturer
• Disconnect power to the appliance before performing any installation or service that requires moving the unit
• Use appropriate tools and safety gear; some installations may require two people to safely position and secure the appliance
• If the appliance requires model-specific brackets or shims, confirm fit with the model's installation instructions before final installation