General Electric Range Hood Parts

This is a replacement interior appliance light bulb that restores illumination inside refrigerators and other household appliances for safer, easier loading and food visibility. Designed to match the original part's fit and basic function. What it does:

• Replaces a failed or dim interior light to restore full illumination
• Sits in the appliance light socket and provides consistent lighting when the door is opened
• Commonly used when the light does not turn on, flickers, or is visibly burned out
• Works as the direct replacement specified by the OEM for compatible models

• One replacement light bulb

• Disconnect power or unplug the appliance before replacing the bulb to avoid electric shock
• Allow the old bulb and housing to cool before removing; use a cloth or gloves to avoid burns and oils from skin
• Remove the bulb cover if present, replace the bulb, then reinstall the cover and restore power
• Dispose of the old bulb per local regulations

This printed circuit is the appliance's electrical control board that manages timed functions and user commands, restoring responsive control and reliable operation when the original board fails. What it does:

• Controls and routes power to user interface, timers, and functional components
• Replaces a failed control board that causes unresponsive buttons or blank/display issues
• Restores correct timing and electronic control when the appliance behaves erratically
• Helps stop intermittent power loss or unexpected cycle interruptions linked to a bad board

• Disconnect power to the appliance before inspecting or replacing the board
• Handle the board carefully; avoid touching components or connector pins to prevent ESD damage
• Verify wiring and connectors match before final assembly; secure all connections

This is a filter clip used on range hoods. It is sometimes referred to as a range hood clip or range hood clamp. There is a filter located inside the range hood that is used to filter out smells and small particles during the cooking process. The filter is held in place by the filter clip. Accidental damage, wear and tear, or misuse may cause the filter clip to fall out or no longer be capable of holding the filter. If the filter clip is missing or broken, a replacement part is required.A visual inspection will determine if the filter clip is damaged or missing. Replacing the clip filter is an easy process. Remove the old filter clip if there is one present. Line up the new filter clip in the same position and snap it into place. Wear gloves for protection. There are no special tools required to make this repair.This is an authentic OEM replacement part. It is sold as an individual unit. The filter clip is made of durable, high-quality materials. The replacement part can be installed in several different models of range appliances. It is compatible with machines produced by General Electric, Hotpoint, and RCA.

5 A, 125 V electrical fuse that restores circuit protection when the original fuse is blown. Replacing the failed fuse helps prevent further electrical damage and can restore normal appliance operation. What it does:

• Provides overcurrent protection for the appliance circuit to stop excessive current flow.
• Replaces a blown or open fuse that prevents the appliance from powering up.
• Common symptom: appliance has no power or a circuit/component won't operate.
• Common symptom: intermittent power or a fuse that visibly shows a blown element.

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing the fuse.
• Replace only with the exact rated fuse (5 A, 125 V) and part number to maintain proper protection.
• Do not bypass the fuse or use makeshift substitutes — that can cause fire or equipment damage.

This motor start/run capacitor helps the appliance motor start and run smoothly, restoring proper motor performance and reducing strain. Replace a failing capacitor to address motor start problems and intermittent operation. What it does:

• Provides the electrical boost motors need to start and maintain RPM
• Helps prevent motor hesitating, sluggish starts, or failure to start
• Can reduce motor overheating and tripping caused by poor starting torque
• Works with the motor's electrical circuit to stabilize operation during run cycles

• Always disconnect power to the appliance before servicing.
• Discharge the capacitor before touching terminals to avoid shock.
• Match wiring and terminal orientation to the original part; secure connections tightly.

This duct-free micro filter system replacement helps capture grease and reduce cooking odors in recirculating microwave/hood installations, restoring proper air recirculation and improving kitchen air quality. What it does:

• Replaces the duct-free micro filter assembly used for recirculating ventilation
• Traps airborne grease and cooking particulates to prevent buildup in the unit
• Helps reduce common cooking odors when the oven/microwave is in recirculation mode
• Visible filter discoloration or heavy grease accumulation are signs it may need replacement

• One replacement duct-free micro filter assembly

• Disconnect power to the appliance before servicing
• Typically installs by accessing the filter area per the appliance service instructions
• Handle the filter gently to avoid damage; dispose of the old filter per local regulations

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

A lampholder bucket that secures the oven/stove lamp socket and positions the bulb for proper illumination. Replaces damaged or melted lamp housings to restore the light assembly and protect wiring from heat. What it does:

• Holds and aligns the oven/stove lamp socket and bulb in the cavity
• Shields the socket and wiring from oven heat and grease
• Helps ensure stable electrical contact for consistent illumination
• Prevents the bulb from shifting or contacting other components

• Disconnect power to the appliance before servicing to avoid shock
• Replace with the exact OEM bucket to ensure correct fit and heat resistance
• Inspect the lamp socket and wiring; replace any damaged components
• Use basic hand tools; refer to the appliance service manual for disassembly steps

Note: This filter is approximately 12" x 14". (Qty of one)

This Grease Filter is an OEM part for GE range hoods. As a key filtration component, this rectangular filter works to capture cooking emissions like grease, smoke and odors above the cooktop. It prevents these contaminants from recirculating back into the kitchen or home.

Causes of a bad filter can include excessive use over time, washing with improper cleaning solutions, or damage during removal/installation.

Symptoms of a bad filter include:

• Reduced airflow and suction from the range hood
• Grease or smoke escaping from the hood despite ventilation usage
• Unpleasant cooking smells lingering in the kitchen

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

24 inch, 20 watts, 4100k, 1200 lumens, T12.

This motor bracket secures the appliance motor to the cabinet, keeping the motor aligned and stable for reliable operation. It's a direct-fit replacement that restores proper motor support and reduces noise from misalignment. What it does:

• Supports and positions the motor so the shaft and pulleys line up correctly
• Prevents excess motor movement that can cause vibration or rubbing noises
• Helps maintain proper belt/pulley tension for effective power transfer
• Restores secure motor mounting after damage or corrosion

• Follow the appliance service manual for removal and reassembly; secure all mounting hardware to the specified torque.
• Disconnect power before starting work to avoid electrical shock.
• Inspect surrounding mounting holes and fasteners; replace any damaged screws or hardware.
• Check belts, pulleys, and motor mounts for related damage.

This ring nut is a small threaded securing nut used to fasten and stabilize appliance fittings and components. It helps keep connections tight and parts properly seated for reliable operation. What it does:

• Secures threaded fittings or assemblies to prevent loosening during use
• Holds components in place on burners, valves, or other hardware where a retaining nut is required
• Worn or stripped ring nuts can cause loose components, rattling, or leaks at connections
• Replacing a damaged ring nut restores proper mechanical retention and alignment

• One ring nut

• Disconnect power and shut off water/gas before starting any repair
• Use the correct-size wrench or socket; start threads by hand to avoid cross-threading
• Tighten snugly but avoid over-torquing, which can strip threads or damage fittings
• Inspect mating threads and any seals or gaskets; replace if damaged

This switch box is the outer housing that protects and organizes oven/stove control switches and wiring, helping keep electrical components secure and stable for reliable cooktop operation. What it does:

• Holds and shields control switches and related wiring from spills, heat, and movement
• Provides secure mounting points for switch terminals to prevent loose connections
• Helps prevent shorting, arcing, and exposure of live wiring
• Restores proper alignment of controls when cracked, melted, or broken

• Disconnect power at the breaker before starting any repair to avoid shock or injury
• Inspect and label wiring before removal; reattach wires to the same terminals
• Handle sharp edges and retainers carefully; some models use clips or screws for attachment
• If switches or wiring are damaged, replace those parts as well for a complete, safe repair