General Electric Range Hood Parts

This grease filter traps airborne grease and cooking particles before they reach the blower and ductwork. Replacing a saturated or damaged filter helps restore vent performance, reduce lingering odors and smoke, and protect the ventilation system from buildup.

• Captures grease and particulates from cooktop exhaust to keep the vent path cleaner
• Helps maintain proper airflow and smoke/steam capture
• Common replacement signs: weak suction, visible saturation, tears/warping, or sagging

• Disconnect power and allow the appliance and filter area to cool before starting
• Open the filter panel/grille; support the filter while releasing tabs or latches
• Note orientation and seating; install the new filter securely without bending it
• Do not operate the vent without a grease filter; test fan operation after installation

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold

This replacement motor restores reliable rotation to the component it powers, helping your appliance operate smoothly and as designed. Swap out a worn or seized motor to bring motion and performance back to normal.

• Supplies rotational power to the attached mechanism inside the appliance
• Common failure symptoms: no movement, humming without turning, grinding/squealing noises, or intermittent/slow operation
• A failed motor can lead to loss of function and unusual noise from the driven part
• Replacing the motor restores proper motion and helps maintain overall performance

• Disconnect power to the appliance before servicing
• Access the motor area; note wire locations and the motor's orientation before removal
• Transfer any brackets, grommets, or screws from the old motor as needed; beware of sharp edges
• After mounting, ensure the shaft/attached part spins freely and clear of obstructions before reassembly and testing

Note: This filter is approximately 12" x 17". (Qty of one)

This Grease Filter is an OEM part for GE range hoods. As a key filtration component, this rectangular filter works to capture cooking emissions like grease, smoke and odors above the cooktop. It prevents these contaminants from recirculating back into the kitchen or home.

Causes of a bad filter can include excessive use over time, washing with improper cleaning solutions, or damage during removal/installation.

Symptoms of a bad filter include:

• Reduced airflow and suction from the range hood
• Grease or smoke escaping from the hood despite ventilation usage
• Unpleasant cooking smells lingering in the kitchen

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This lamp holder support secures the appliance's light socket in the proper position so your lighting stays steady and reliable. Replace a cracked or heat-damaged support to keep the bulb and wiring stable and the work area/interior well lit.

• Holds the lamp socket/holder firmly in place to prevent movement and vibration
• Helps restore consistent lighting when the bulb and fuse test good
• Common symptoms: light flickers or cuts out when the door is used or when bumped
• Visible signs include broken tabs/clips, warping, or heat damage on the support

• Disconnect power and allow the appliance to cool before servicing
• Access the lamp area by removing the appropriate cover or panel as directed by your service manual
• Transfer the socket and wiring to the new support; avoid pinching or straining wires
• Handle bulbs with care and test operation before reassembly

This ring nut is a small threaded retaining nut that secures a mating component to its shaft or connection, restoring a stable mechanical or sealed connection and reducing movement or leaks when properly installed. What it does:

• Holds a shaft, tube or fitting in place by threading onto the mating component
• Prevents components from working loose and reduces rattling or vibration
• Helps maintain a sealed connection where used on fittings or hose connections
• Useful when a stripped or missing nut causes loose hardware or intermittent operation

• One ring nut

• Disconnect power and shut off water before beginning work
• Inspect mating threads and replace if damaged; clean threads before installing
• Hand-start threads to avoid cross-threading, then tighten with appropriate tool; avoid overtightening

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

Solid-state triac that switches AC power under command of the appliance's electronic control board. Replacing a failed triac restores proper power control to heating elements or motors and resolves intermittent or no-power symptoms. What it does:

• Acts as a solid-state switch on the control board to regulate AC power to heating elements or motors
• Enables the electronic control to modulate output for temperature or speed control
• Failure can cause no heat, intermittent heating, or loss of motor control
• Designed to match the original control circuit; check board mounting and connections before replacing

• Always disconnect all power at the breaker or unplug the appliance before servicing — risk of electric shock
• This part mounts to the control board; handle the board and connectors carefully to avoid damage
• Use anti-static precautions when handling electronic components;
• Verify the part number on the original board before installation

This lamp socket holds the appliance light bulb and provides the electrical connection it needs, restoring reliable, steady lighting so you can see clearly during cooking and routine checks.

• Provides secure electrical contact to power the light bulb
• Holds the bulb firmly in the light assembly
• Replaces heat-damaged or brittle sockets that cause flickering or no light
• Common symptoms: light won't turn on with a known-good bulb, flickers, bulb won't seat, or visible charring/melting at the socket

• Disconnect power at the breaker and allow the appliance to cool before service
• Wear cut-resistant gloves; nearby metal and glass edges can be sharp
• Move wires one at a time from the old socket to the new to maintain correct connections
• Install a bulb that matches your model's specified type and wattage before restoring power

This grease filter screens cooking vapors drawn through the vent system to capture grease and protect the blower and ductwork, helping maintain clear airflow. Replace a saturated or damaged filter to keep ventilation performance consistent. What it does:

• Traps airborne grease and particulates before they reach the fan and ducting
• Helps maintain proper airflow and vent performance
• Replace if the filter is heavily coated, torn, dented, or deformed
• Smoke or steam lingering more than usual can indicate a clogged filter

• One grease filter

• Disconnect power to the appliance and allow surfaces to cool before service
• Support the filter while releasing the retaining tabs or clip to remove it
• Install the new filter in the same orientation; ensure tabs/clips are fully engaged
• Do not operate the fan without a grease filter installed

This lampholder is the light socket that secures the bulb and delivers power so your appliance lighting works reliably. Replace a worn or heat-damaged socket to restore steady illumination and dependable operation.

• Provides secure mounting and proper electrical contact for the light bulb
• Fixes issues such as no light, flickering, or bulbs that won't stay seated even after replacement
• Replaces sockets with visible cracks, discoloration, or burned contacts
• Uses the bulb type and wattage specified for your model

• Disconnect power at the breaker or unplug the appliance before servicing
• Use only the bulb type and wattage listed for your appliance; seat the bulb fully without overtightening
• Transfer any mounting screws, bracket, or connectors from the original part as required by your model

This is a replacement control knob in black with stainless trim for select cooking appliances. It restores a secure grip and accurate selection of heat or functions when the original knob is cracked, stripped, missing, or worn.

• Attaches to the control shaft to adjust burner heat or oven settings
• Replaces knobs that are cracked, stripped, loose, or missing
• Restores proper control feel and setting alignment
• Finish: black with stainless trim to match the original

• Disconnect power; if applicable, shut off gas and let all surfaces cool
• Pull the old knob straight off the stem
• Align the new knob's opening with the control stem and press straight on—do not force
• Verify correct orientation and smooth operation through all settings

A blower assembly that circulates oven or range heat to support convection cooking. Replacing a worn or failed blower restores airflow for more even cooking and reduces noisy or grinding fan operation. Sold individually. What it does:

• Circulates hot air across the oven cavity to support convection and temperature consistency.
• Restores airflow that helps prevent uneven cooking or extended bake times when the blower fails.
• Common symptoms of failure: loud or grinding noise, little or no airflow from the convection fan, or reduced baking performance.
• Replaces assemblies that are worn, seized, or producing excessive vibration.

• Disconnect electrical power (and gas supply, if applicable) before starting any service.
• Allow the appliance to fully cool; remove access panels to reach the blower.
• Handle fan blades carefully to avoid damage; verify the blower spins freely and wiring connectors are secure before reassembly.

This replacement fan blade restores proper airflow inside your microwave, helping cool internal components so the unit runs reliably and quietly. A worn or damaged blade can reduce ventilation and lead to noise or overheating during operation.

• Circulates air to help cool internal parts and maintain proper airflow
• Helps reduce humming, rattling, or scraping noises from a damaged or unbalanced fan
• Can address weak or no airflow from the fan area
• May help prevent overheating or thermal shutdowns caused by poor circulation

• Disconnect power to the microwave before servicing to avoid electrical shock
• Access the fan area; remove grille/panels as required
• Note blade orientation; transfer any clips, spacers, or hardware from the original
• After installation, spin the blade by hand to ensure free movement before restoring power

This fan control switch operates the fan motor to regulate blower speed and restore proper airflow in affected appliances. A direct-fit replacement designed to return fan control without reworking wiring or mounting. What it does:

• Selects and maintains fan speed for proper airflow and cooling
• Restores fan operation when the blower won't run or only runs at one speed
• Helps resolve noisy, intermittent, or non-responsive fan behavior
• Works as the user-facing control that communicates speed settings to the fan motor

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools; avoid forcing connectors or terminals