General Electric Range Hood Parts

This hex nut secures components within the range or cooktop assembly, helping keep parts tight and aligned. Replace a missing, stripped, or corroded nut to restore a solid fit and reduce rattling or loosening during use.

• Provides threaded fastening to hold mating parts together securely
• Replaces worn, stripped, or rusted hardware that no longer tightens properly
• Can help resolve loose or wobbly components and rattling noises
• Built to match the original fastener for proper fit in compatible appliances

• Disconnect power and shut off gas before servicing
• Start threads by hand to avoid cross-threading; tighten only until snug with the appropriate wrench
• Note the order of any washers/spacers during removal to ensure correct reassembly

This bezel is a small trim piece that finishes an opening on the appliance's control area. It restores a clean, factory look and helps protect the underlying panel when the original is cracked, loose, or missing.

• Frames the control opening for a finished appearance
• Helps shield panel edges from wear and debris
• Typical symptoms: cracked plastic, broken tabs, discoloration, loose or missing trim

• Disconnect power and allow the appliance to cool before servicing
• Remove any adjacent knob or trim as needed for access
• Release the old bezel's tabs or screws and note its orientation
• Install the new bezel in the same position, then reinstall removed parts and test

This replacement motor powers the blower in your ventilation unit, spinning the fan blade or wheel to move air through the housing and ductwork. Replace it when the original motor becomes noisy, stalls, or fails to start.

• Drives the fan blade/blower wheel to move air through the unit
• Restores proper airflow and ventilation performance
• Common symptoms: loud humming or grinding, won't start, slow/weak airflow, intermittent operation, overheating/shutting off
• Often needed when the shaft is seized or bearings are worn

• Disconnect power at the breaker before servicing
• Access the blower assembly; remove the grille or filters to reach the motor
• Note wire locations; transfer wiring, mounting hardware, and the fan blade/blower wheel from the old motor if applicable
• Ensure the blade/wheel spins freely before reassembly, then restore power to test

This lamp holder support secures the appliance's light socket in the proper position so your lighting stays steady and reliable. Replace a cracked or heat-damaged support to keep the bulb and wiring stable and the work area/interior well lit.

• Holds the lamp socket/holder firmly in place to prevent movement and vibration
• Helps restore consistent lighting when the bulb and fuse test good
• Common symptoms: light flickers or cuts out when the door is used or when bumped
• Visible signs include broken tabs/clips, warping, or heat damage on the support

• Disconnect power and allow the appliance to cool before servicing
• Access the lamp area by removing the appropriate cover or panel as directed by your service manual
• Transfer the socket and wiring to the new support; avoid pinching or straining wires
• Handle bulbs with care and test operation before reassembly

This lamp switch controls power to the appliance's light circuit. It turns the light on and off via the door mechanism or controls, restoring visibility inside the cavity and fixing issues like a light that won't turn on or off. What it does

• Controls the on/off function of the lamp circuit
• Activates or deactivates the light with the door or control input (as designed for the model)
• Common fix for a light that won't turn on, stays on continuously, or works intermittently
• Replaces a switch with worn, stuck, or inconsistent contacts

• 1 lamp switch

• Disconnect power before servicing; if working on a microwave, be aware of high-voltage components
• Access is typically behind the control panel or latch area; remove mounting screws/panels as needed
• Note wire positions (COM/NO/NC) and transfer one at a time to the new switch
• Verify switch orientation, secure in bracket, and test light operation before reassembly

A blower assembly that circulates oven or range heat to support convection cooking. Replacing a worn or failed blower restores airflow for more even cooking and reduces noisy or grinding fan operation. Sold individually. What it does:

• Circulates hot air across the oven cavity to support convection and temperature consistency.
• Restores airflow that helps prevent uneven cooking or extended bake times when the blower fails.
• Common symptoms of failure: loud or grinding noise, little or no airflow from the convection fan, or reduced baking performance.
• Replaces assemblies that are worn, seized, or producing excessive vibration.

• Disconnect electrical power (and gas supply, if applicable) before starting any service.
• Allow the appliance to fully cool; remove access panels to reach the blower.
• Handle fan blades carefully to avoid damage; verify the blower spins freely and wiring connectors are secure before reassembly.

This blower assembly circulates air through the appliance to maintain proper airflow and ventilation. Replacing a worn or damaged assembly restores efficient exhausting and reduces unusual noises or poor airflow. What it does:

• Moves air through the appliance for proper ventilation and drying/performance
• Helps expel humidity, lint, and combustion byproducts
• Can resolve reduced airflow, weak performance, or excessive noise from the blower area
• Supports consistent temperature and cycle performance by maintaining airflow

• 1 blower assembly

• Disconnect power (and gas if applicable) before starting any repair
• Handle the blower carefully; edges and mounting tabs can be sharp
• Secure all mounting screws and duct connections
• Check lint traps and ducts for blockages when replacing the blower

This lamp switch controls the oven interior light, letting you turn the light on or off from the range/oven control panel. Replaces a worn or non-working light switch to restore oven lighting control. What it does:

• Acts as the control for the oven interior lamp when you press the switch
• Commonly used when the light won't turn on, flickers, or the switch feels loose
• Provides a direct electrical connection between the oven lighting circuit and the lamp
• Matches OEM fit and function for compatible GE ranges and ovens

• 1 lamp switch

• Disconnect power to the appliance before servicing to avoid shock
• Basic wiring and panel access are required; keep track of mounting screws and wire locations
• Only install parts intended for your appliance model

The Main Control Board is an OEM component specifically designed for GE range hoods. It serves as the central processor responsible for monitoring and regulating all critical operations of the hood through the precise activation of electronic relays and components. The main control board facilitates programmed lighting and motor speed settings according to sensor inputs.

Symptoms of a bad main control board include:  

• Failure to turn on lights or adjust ventilation levels
• Sensor malfunctions triggering alarms  
• Display errors or inconsistent responses to commands
• Intermittent or dead operations unexplained 

Causes can involve power surges, water damage or worn traces/connections due to age.

This OEM GE replacement is compatible with Hotpoint, RCA and some Kenmore hoods as well.

This switch panel is the front control surface that houses the oven/range switches and user controls, restoring reliable input and visible indicators so you can select settings and operate the appliance with confidence. What it does:

• Provides the mounted switches and contact points for oven/range functions
• Transfers button presses to the control assembly so selections register correctly
• Restores visible indicators and tactile control when worn or damaged
• Commonly replaced when buttons stick, controls fail to engage, or the panel is cracked

• Disconnect power to the appliance before beginning any work to avoid shock
• Handle carefully to avoid damaging switch contacts, wiring, or cosmetic surfaces
• May require removing the console or back panel to access mounting screws and wiring harnesses

This cover plate is a factory-style trim panel that protects and finishes the appliance's control area and internal components, restoring a clean appearance and helping keep wiring and switches shielded from debris. What it does

• Covers and protects the appliance control area and underlying components
• Restores a finished look to a damaged or missing trim panel
• Helps prevent dust and spills from reaching electrical parts or switches
• Matches OEM fit and mounting points for a secure replacement

• One cover plate (trim panel)

• High-level replacement; typically removed and installed with basic hand tools
• Disconnect power to the appliance before starting to avoid shock or injury
• Inspect mounting clips and fasteners and replace if worn for a secure fit

This blower and motor assembly moves air through the appliance to support proper ventilation and heating. Replacing a worn assembly restores airflow and can reduce noise or overheating caused by a failing blower. What it does:

• Spins the blower wheel to circulate air through the appliance's airflow path
• Restores normal ventilation and heat distribution when the blower stops working
• Reduces rattling, grinding, or whistling noises from a worn motor or fan
• Helps prevent overheating or poor performance caused by restricted or non-moving airflow

• One blower and motor assembly as shown

• Disconnect all power before beginning service to avoid shock or injury
• Handle the assembly carefully to avoid bending the blower wheel or damaging wiring
• Basic hand tools typically required; follow appliance service manual for disassembly steps

This motor start/run capacitor helps the appliance motor start and run smoothly, restoring proper motor performance and reducing strain. Replace a failing capacitor to address motor start problems and intermittent operation. What it does:

• Provides the electrical boost motors need to start and maintain RPM
• Helps prevent motor hesitating, sluggish starts, or failure to start
• Can reduce motor overheating and tripping caused by poor starting torque
• Works with the motor's electrical circuit to stabilize operation during run cycles

• Always disconnect power to the appliance before servicing.
• Discharge the capacitor before touching terminals to avoid shock.
• Match wiring and terminal orientation to the original part; secure connections tightly.

This plastic screw visor is the small trim screw cover that protects and hides the fastener on appliance control panels and exterior trim. It keeps the appearance tidy and prevents dirt from collecting around exposed screw heads. What it does:

• Covers and conceals a panel or trim screw to restore original appearance
• Protects the screw head from dirt, moisture and accidental contact
• Helps maintain a finished look on control panels, bezels and exterior trim
• Commonly used where small plastic caps are needed to match factory styling

• Simple push-on or snap-fit installation; press into place over the screw head
• Use standard hand tools to access screw; disconnect power to the appliance before servicing
• Replace any damaged surrounding trim clips or screws for secure fit

This 10-24 x 3/16" screw is a replacement fastener used to secure panels, brackets, or components in compatible appliances. It restores proper fit and helps prevent vibration or parts coming loose during operation. What it does:

• Secures trim, panels, or internal brackets where a 10-24 thread and short 3/16" length are required
• Replaces missing or stripped screws that cause rattling or loose components
• Restores proper alignment of parts held by this fastener
• Works wherever OEM specifies a 10-24 x 3/16" screw for reliable fastening

• One (1) 10-24 x 3/16" screw

• Use the correct screwdriver or driver bit sized for the screw head to avoid stripping
• Tighten until snug; avoid over-torquing which can strip threads or damage components
• Disconnect power and follow appliance safety precautions before accessing internal parts
• If fastening into plastic, avoid excessive force