General Electric Room Air Conditioner Parts

This air filter traps dust and lint before they reach the evaporator in your room air conditioner, helping maintain airflow and cooling performance. Replacing a damaged or missing filter protects the coil and keeps the unit running efficiently. What it does:

• Screens incoming air to help keep the evaporator coil clean
• Helps maintain proper airflow and cooling performance
• Replace if torn, warped, or excessively soiled
• Common symptoms: weak airflow, reduced cooling, or a filter that won't stay seated

• 1 air filter

• Disconnect power before opening the front panel
• Open the grille/access panel, remove the old filter, and note its orientation
• Slide the new filter fully into the track; ensure it sits flat and secure
• Do not operate the air conditioner without a filter; follow the owner's manual for care

Color: tan. Measures about 1-1/2 inches in diameter.

This replacement air filter for room air conditioners traps dust and lint before they reach the coils and blower, helping maintain airflow and cooling performance when the original filter becomes clogged, damaged, or missing.

• Captures dust and lint from return air to protect internal components
• Helps maintain proper airflow for consistent cooling
• Reduces debris recirculation into the room
• Replace if torn, warped, or permanently clogged; symptoms can include weak airflow, longer run times, and poor cooling

• Disconnect power before servicing the unit
• Open or remove the front grille per your model's design
• Slide out the old filter; insert the new filter in the same orientation until fully seated
• Restore power and check airflow

This transformer converts incoming household voltage to the specific levels needed by your appliance's circuits and components. Replacing a failed unit restores stable power delivery so controls and critical loads operate correctly and safely. What it does

• Steps line voltage up or down to supply connected circuits
• Provides isolated, stable power for control or heating components
• Failure symptoms include: unit won't power on or run, internal fuse repeatedly blows, loud humming/buzzing, or signs of overheating near the transformer

• 1 transformer assembly

• Disconnect power at the breaker and before servicing
• Label or photograph wire locations and move leads one at a time to matching terminals
• Inspect related fuses, wiring, and connectors before reapplying power

This Drive PWB is the replacement electronic board that controls the appliance's drive functions, restoring reliable motor and transmission commands for normal operation. What it does

• Controls drive motor speed and direction and sends/receives signals to the main control
• Can resolve symptoms such as no spin/agitate, erratic drive behavior, or unresponsive drive controls
• Re-establishes communication between drive assembly and console when board failure is the cause
• Works as the direct replacement board for the drive electronics in compatible units

• Disconnect power to the appliance before service to avoid shock—verify unit is de-energized
• Handle the board by its edges and avoid touching components; observe basic ESD precautions
• Reconnect all connectors in their original positions and secure mounting hardware

This axial flow fan moves air through the appliance to help cool internal components and support proper airflow. Replacing a worn or damaged fan restores quiet operation and helps prevent overheating-related issues. What it does:

• Circulates air across internal components or heat exchangers to maintain proper operating temperatures
• Helps prevent overheating of electronics, motors, or heating elements
• Reduces abnormal noise caused by worn or imbalanced fan blades or bearings
• Supports consistent airflow for reliable appliance performance

• One axial flow fan assembly

• Disconnect power to the appliance before starting any repair
• Handle the fan blades carefully to avoid damage; align properly during installation
• Verify secure mounting and electrical connections before restoring power
• Test appliance operation after installation and observe for proper airflow and quiet operation

This control base assembly is the molded housing that holds the appliance's user-interface components. Replacing a damaged base restores proper alignment and secure mounting of the control board, switches, and display for dependable operation.

• Provides structural support and mounting points for the control board, switches, and display in the control area
• Keeps buttons/knobs aligned for smooth, consistent actuation
• Helps protect and organize wiring within the control panel
• Typical symptoms: cracked or broken housing, loose or sunken controls, buttons sticking or not lining up, rattling/vibration from the control area

• Disconnect power to the appliance before servicing
• Remove the control panel/console to access the base; retain screws and clips for reuse
• Transfer existing control components and wiring to the new base in the same positions
• Avoid overtightening screws into plastic; verify button travel and alignment before reassembly

A fan motor run capacitor that helps the appliance fan start and maintain smooth operation. Replacing a failed capacitor restores proper airflow and can help recover normal cooling performance when the original part wears out. What it does:

• Provides the phase shift and stored energy needed for the fan motor to start and run reliably.
• Common symptoms of a failing capacitor: fan not starting, fan humming or running intermittently, reduced airflow, or poor cooling performance.
• Used where a dedicated run capacitor is required for the appliance fan motor.
• Does not include installation tools or wiring harnesses.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Capacitors can hold a charge; discharge safely before touching terminals or disconnecting wires.
• Note terminal wiring positions (take a photo) to ensure correct reconnection.

This main control PWB is the appliance's primary electronic control board that manages user inputs and cycle functions, restoring normal control when a faulty board causes operational issues. What it does:

• Receives user commands and runs appliance control algorithms
• Powers and updates the touchpad/display and indicator lights
• Manages timing, relay switching, and communication with sensors
• Common symptom: appliance won't start, has a blank or erratic display, or shows control-related error codes
• Helps correct unresponsive buttons, intermittent operation, or unexpected cycle behavior when board failure is confirmed

• Disconnect power (unplug or shut off breaker) before accessing the control board
• Handle the PWB by its edges and avoid static discharge; use ESD protection if available
• Refer to the appliance wiring diagram and service manual for proper connector placement and safety procedures

A rubber compressor cushion that isolates the compressor from the refrigerator chassis to reduce vibration and prevent metal-on-metal contact. Replaces worn or missing cushions to help minimize noise and vibration transfer. What it does:

• Cushions the compressor to dampen vibration and reduce rattling or buzzing noises.
• Keeps the compressor from directly contacting the cabinet, preventing wear and chafing.
• Helps maintain proper compressor positioning and reduces stress on mounting components.
• Common symptom: increased compressor noise or vibration, or visible worn/deteriorated cushion.

• One compressor cushion (rubber mount).

• Disconnect power to the appliance before starting any repair.
• Support the compressor or secure the unit when removing/replacing mounts to avoid strain.
• Remove the old cushion and press the new cushion into place; no refrigerant handling required.
• Use basic hand tools and wear gloves.

This safety device protects the compressor by interrupting power if it overheats or draws excessive current. Replacing a weak or failed protector restores reliable starts and helps prevent nuisance shutdowns and compressor damage.

• Opens the compressor circuit during overheat/overload to prevent motor damage
• Common symptoms include: compressor won't start, clicks and briefly hums, or starts then quickly shuts off
• Can contribute to poor cooling while fans or controls still operate
• Visual clues may include heat discoloration or damaged terminals at the protector

• Disconnect power before servicing; capacitors in the system can retain a charge—discharge safely
• Access the compressor terminal cover; note wire locations and remove the old protector
• Inspect terminals/connectors; replace any burnt or loose spade connectors for a secure fit
• Fully seat the new protector on the compressor terminal and reconnect wires firmly; check any companion start relay or capacitor if symptoms persist

This adapter is a small connector used to join compatible appliance lines or fittings, restoring a secure connection and preventing leaks or loss of function. It's a direct replacement when the original adapter is cracked, corroded, or damaged. What it does

• Connects two mating hoses, tubes, or fittings to re-establish a sealed pathway
• Restores proper flow and helps stop leaks from worn or broken adapters
• Commonly used where a compact, durable coupling is required
• Works as a like-for-like replacement when the original adapter is missing or damaged

• One adapter

• Disconnect power and shut off water or supply lines before servicing
• Verify matching thread type/orientation before installation to avoid cross-threading
• Hand-start threads, then tighten to manufacturer torque; do not overtighten
• Inspect for leaks after restoring power/supplies and running the appliance

This curtain assembly replaces the inner door curtain on compatible GE over-the-range and countertop microwaves to restore the door's interior cover and help maintain proper operation and shielding. It's a direct-fit replacement sold individually. What it does:

• Replaces a cracked, warped, or missing inner door curtain that can expose internal components
• Helps restore the door interior, which can reduce visible light leaks and improve door integrity
• Addresses issues such as rattling or loose interior door panels during operation
• Compatible with service procedures that require removing and replacing the door inner curtain

• 1 curtain assembly

• Unplug or disconnect power before starting any repair; service only with unit de-energized
• Handle door components carefully to avoid damaging glass, seals, or the new curtain
• Removing the outer door and/or inner door liner may be required;

This evaporator blower fan blade circulates cold air through the refrigerator to maintain even cooling and proper frost control. Replacing a worn or broken blade restores airflow and helps the appliance cool more consistently. What it does:

• Spins on the evaporator motor to move air across the evaporator coils
• Promotes even temperature distribution inside the fresh-food and freezer compartments
• Helps prevent frost build-up by maintaining steady airflow
• Commonly replaced when airflow is weak, the fan is noisy, or the blade is cracked or broken

• One fan blade

• Disconnect power before accessing the evaporator/fan area to avoid shock or injury
• Handle the blade carefully to avoid bending fins or damaging the motor shaft
• The motor shaft and mounting hardware are intact before installation

This transformer supplies the low-voltage power needed by the appliance's control and ignition systems, restoring proper operation of electronic controls and spark ignition when the original transformer fails. What it does:

• Converts incoming mains power into the low-voltage output used by control boards and igniters
• Supports reliable spark generation for gas ignition systems on compatible appliances
• Helps restore responsive electronic controls and displays when a failed transformer causes loss of power
• Prevents intermittent control or ignition failures caused by a defective transformer

• One transformer

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle wiring harnesses and connectors carefully; ensure secure connections and proper routing