General Electric Room Air Conditioner Screws, Nuts, Washers

This is a single replacement bolt used to secure appliance components and restore proper fit and function. A simple, direct fastener that replaces worn, stripped, or missing hardware to stop movement and noise. What it does

• Secures panels, brackets, or assemblies to prevent shifting or sagging
• Restores clamped connections that can cause rattling or vibration
• Replaces stripped or missing hardware that may cause misalignment
• Helps maintain safe, stable operation of the repaired component

• One replacement bolt

• Turn power off and unplug the appliance before beginning any repair
• Confirm screw type and length match the original before installation
• Use appropriate hand tools and torque; avoid overtightening to prevent stripping
• If other fasteners look worn, replace them together for a secure repair

A replacement mounting nut used to fasten appliance panels, brackets or assemblies so parts stay secure and stable during operation. Durable, low-profile design restores proper fit and reduces movement or rattling. What it does:

• Secures mounting studs, brackets or components to maintain proper alignment
• Prevents loosening that can cause vibration, noise or misaligned panels
• Helps keep electrical and mechanical assemblies firmly connected for reliable performance
• Fits in tight spaces where a low-profile hex flange nut is required

• Disconnect power and water before starting any repair
• Use the correct socket or wrench size; avoid stripping threads by hand-starting the nut
• Tighten snugly but do not over-torque to prevent thread or component damage
• If threads are damaged or corroded, replace the mating fastener or stud as well

This small replacement nut secures appliance components and hardware to keep assemblies stable and operating quietly. It's a simple, direct fix when a loose or missing nut causes rattling or unstable mounting. What it does:

• Secures panels, brackets, or components to prevent movement and vibration
• Restores proper hardware retention when the original nut is stripped, missing, or damaged
• Helps eliminate rattling, loose knobs, or misaligned parts caused by failed fasteners

• Disconnect power and shut off water before servicing the appliance
• Use the correct wrench or socket size and hand-start threads to avoid cross-threading
• Tighten snugly but avoid overtightening, which can strip threads or damage components

This flat metal washer provides a reliable spacer and load distributor for fastening points in the washer assembly, helping maintain proper alignment and secure connections for moving parts. What it does:

• Sits under a nut or bolt to distribute pressure and protect mating surfaces
• Helps maintain proper spacing and alignment of rotating or fastened components
• Can reduce loosening from vibration when used with the correct fastener
• Symptoms of a failed/missing washer: loose fittings, excessive play, noise or intermittent loosening

• One flat metal washer as shown

• Verify correct orientation and placement before torquing the fastener
• Replace any damaged or corroded fasteners along with the washer for best results
• Follow manufacturer torque specs and safety procedures when servicing
• Disconnect power and water and use appropriate tools and PPE

This flat washer provides a durable bearing surface for a fastener, helping secure assemblies and reduce wear between parts. It's a simple replacement that restores proper spacing and fastening where the original washer is worn or missing. What it does:

• Provides a stable bearing surface for bolts, screws, or shafts
• Helps maintain correct spacing and alignment of adjacent parts
• Reduces metal-on-metal wear and prevents premature component damage
• Can stop looseness, vibration, or rattling caused by a worn or missing washer

• Disconnect power and shut off water before starting any repair
• Verify orientation and position against the original part before installing
• Use the correct fastener and torque to avoid over-compressing the washer

This nut-washer secures appliance assemblies where a captive nut and flat washer are needed, helping keep fasteners tight during normal operation. It's a small replacement part that prevents loosening and maintains proper component alignment. What it does:

• Acts as a combined nut and washer to fasten components and distribute load
• Keeps threaded connections from backing off due to vibration
• Restores secure attachment when the original nut-washer is damaged, stripped, or missing
• Commonly replaced when assemblies wobble, rattle, or come loose

• One nut-washer

• Disconnect power and unplug the appliance before beginning any repair
• Use the proper screwdriver or socket to avoid rounding the fastener
• If threads are damaged, replace the mating screw or stud rather than over-tightening

A small OEM special screw used to secure appliance panels and components for safe, quiet operation. Replaces a missing or stripped screw to restore proper fit and reduce vibration and rattling. What it does:

• Secures panels, trim, or internal components to maintain alignment and prevent movement
• Stops rattling or vibration caused by a missing or loose screw
• Helps maintain proper grounding/attachment points when used as intended
• Matches factory fit and thread form for reliable fastening

• Turn off and unplug the appliance before inspecting or replacing hardware
• Use the proper driver to avoid stripping the head; tighten until snug but do not overtighten
• If the original screw is corroded or broken, remove remaining fragments carefully to avoid damage