General Electric Washer Dryer Combo Support Parts

The Front Drum Support is an OEM part for GE dryers. It supports the front of the dryer drum, allowing it to rotate smoothly during the drying cycle. This support helps maintain the drum's position and alignment, ensuring efficient and quiet operation.

You should replace the front drum support if it becomes worn out or damaged. Causes of a bad drum support can include regular wear and tear from continuous use, overloading the dryer, or debris causing friction and damage.

Symptoms of a bad front drum support include:

• Unusual noises such as squeaking or grinding during operation
• The drum not rotating smoothly or becoming misaligned
• Clothes taking longer to dry or uneven drying
• Visible wear or damage to the support structure

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This fork support actuator assembly mounts in the washer's drive mechanism and supports the shift fork that changes between wash/agitate and spin. Replacing a worn assembly restores dependable shifting and helps resolve no-agitate, no-spin, and grinding complaints. What it does:

• Supports and guides the mode-shifter fork within the drive system
• Enables proper engagement of agitation and spin functions
• Helps maintain alignment to reduce mis-shifts and noise
• Can cause: won't agitate, won't spin, loud clicking/grinding, intermittent shifting

• 1 fork support actuator assembly

• Disconnect power and shut off water supply before service
• Access location varies by model
• Note linkage orientation before removal; transfer any reusable clips/screws
• After installation, run a test cycle to ensure proper mode changes

This transmission and support assembly drives and stabilizes the wash basket. It converts motor power into agitation and spin while supporting the tub, helping resolve no-agitate/no-spin complaints and loud operation for reliable cleaning performance.

• Transfers motor power to the drive system for agitation and spin
• Supports the basket and helps maintain alignment during operation
• Helps correct no agitate, no spin, or weak/intermittent spin
• Can address grinding/rumbling noises or oil traces from the center

• Disconnect power and water before servicing; wear gloves and eye protection
• Appliance and assembly are heavy—use assistance and protect flooring
• Removal typically requires accessing from top and bottom to remove agitator/basket and drive hardware
• After installation, run a test cycle to ensure smooth agitation, proper spin, and no leaks

This supports assembly stabilizes and supports the washer's internal moving components, keeping them properly aligned to control vibration during wash and spin. Replacing a worn support can restore smoother operation and reduce excessive shaking or noise. What it does:

• Supports and stabilizes the tub/drive system during agitation and spin
• Helps absorb vibration to minimize shaking, banging, and noise
• Maintains proper alignment to prevent rubbing or scraping
• Typical failure signs: excessive vibration, out-of-balance interruptions, knocking sounds, or the washer "walking"

• 1 supports assembly

• Disconnect power and water before servicing; wear gloves and eye protection
• Access the assembly by removing the appropriate cabinet/top or front panel per your model's service information
• Safely support the tub/drive to relieve load before removing fasteners and swapping the assembly
• Transfer any model-specific brackets or hardware as needed; the washer is level before test run

This control support is the mounting bracket that secures the appliance control assembly, keeping the control panel stable and aligned for reliable operation. Replaces a worn or broken support to restore proper panel fit and reduce vibration. What it does:

• Holds the control board/panel in place to prevent sagging or misalignment
• Keeps control knobs and buttons properly positioned for accurate use
• Reduces vibration and rattling that can affect button/knob response
• Can prevent intermittent contact caused by a loose or damaged support

• One control support bracket

• Disconnect power (unplug the appliance or shut off the breaker) before starting any work
• Access usually requires removing the control panel or back panel; keep fasteners organized
• Install with original mounting screws; inspect surrounding clips and hardware for wear

This panel motor cradle is a molded mounting bracket that secures the panel motor assembly, keeping the motor properly positioned so the control panel or dispenser mechanism operates smoothly and quietly. What it does:

• Holds and stabilizes the panel motor to prevent misalignment or rubbing
• Maintains correct motor-to-gear engagement for reliable panel movement
• Reduces vibration and noise from a loose or damaged motor mount
• Helps prevent wear on motor shafts and surrounding components

• One panel motor cradle bracket

• Disconnect power to the appliance before beginning any service
• Requires basic hand tools; access may require removing the control panel or console
• Inspect adjacent parts (fasteners, motor, gears) and replace if worn