General Electric Washer Dryer Combo Screws, Nuts, Washers

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.

This is a self-tapping sheet metal screw (8-18) used to secure internal components within the dryer. It threads into metal panels or brackets to hold parts firmly in place during operation. Replace if the screw is stripped, missing, or corroded, which can cause loose panels, rattling noises, or components shifting out of position.

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Terminal block mounting screw for dryers and washer dryer combos. Secures the terminal block to the dryer frame. Replace if stripped, missing, or damaged.

A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:

• Fastens panels, brackets, and small parts in household appliances
• Replaces stripped, rusted, or missing #8-18 pan head screws
• Restores secure mounting where vibration or wear caused looseness
• Works with sheet-metal or threaded inserts designed for #8-18 screws

• Disconnect power to the appliance before beginning any repair
• Use the correct #2 Phillips or compatible driver to avoid cam-out
• Thread in straight and tighten until snug; avoid over-tightening to prevent stripping
• Keep small screws away from children and dispose of old fasteners safely

5/16-18 hex screw secures panels and components in laundry centers. Replace stripped, broken, or missing fasteners to restore proper fit and alignment.

Hex pan thread screw for washer dryer combo units. Secures panels and components to the frame. Replace missing, stripped, or damaged fasteners.

Replacement hex washer head screw for laundry center panels and components. Needed when original fasteners are stripped, missing, or damaged during repair.

Gas supply pipe for dryers. Connects the gas valve to the burner assembly. Replace if cracked, corroded, or leaking to restore safe gas flow to your dryer.

8-18 x 5/8-inch Torq II screw secures panels, brackets, and trim on laundry centers. Replace stripped, missing, or damaged screws to restore fit.

Replacement 10-24 x 3/8 machine screw for washer dryer combos. Secures panels, brackets, and internal components. Needed when original screws are lost, stripped, or damaged during service. Restores proper fastening.

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly