General Electric Washer Dryer Combo Clip Or Clamp

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This locking clip secures a mating component inside the washer, keeping it firmly attached to its mounting point. Replacing a worn or missing clip restores a snug fit and helps prevent movement, intermittent connections, and noise during operation.

• Retains the designated component securely to its bracket or panel
• Helps prevent vibration-related movement, rattling, or disconnection
• Maintains proper alignment for consistent operation
• Typical signs of failure: cracked or missing clip, part won't stay seated, new looseness around the mount

• Disconnect power and turn off water before servicing
• Access the clip location per your model's service information
• Release and remove the old clip; inspect the mating part for damage or wear
• Seat the new clip fully until it locks; verify the component is secure before reassembly

A replacement tub outlet clamp that secures the drain boot or hose to the washer tub outlet to help prevent leaks and hose separation. Simple, durable hardware designed to restore a secure water-tight connection. What it does:

• Fastens the drain boot or outlet hose to the tub outlet to stop leaks at the connection.
• Keeps the drain hose or boot from slipping off during the wash cycle.
• Restores a tight, stable seal after worn or damaged clamps cause leaking.
• Works with the tub outlet/boot assembly to maintain normal drain flow.

• One tub outlet clamp.

• Disconnect power to the appliance before beginning any repair.
• Turn off water supply and drain any remaining water from the tub to avoid spills.
• Use appropriate pliers or a screwdriver (depending on clamp type) to remove the old clamp and secure the replacement.
• Inspect the boot/hose and tub outlet for damage; replace damaged components as needed for a reliable seal.

This small replacement clip secures the draining hose to the appliance, helping keep the hose in the correct position and preventing kinks, rubbing, or unintended movement that can cause leaks or drainage issues. What it does:

• Holds the draining hose in place to prevent sagging or rubbing against sharp edges
• Helps maintain proper hose routing for reliable draining
• Reduces the risk of hose chafing that can lead to leaks
• Simple mechanical part — no electrical function

• Disconnect power and water supply to the appliance before starting any work
• Locate the draining hose routing and remove the old clip, if present
• Snap the new clip onto the hose and secure it to the frame or mounting point until it clicks
• Inspect the hose path after installation; ensure the hose is seated and not kinked

This replacement part is a dryer clip, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This dryer clip is typically found on dryers and there are usually multiple clips on one appliance. These clips help hold the front panel in place and secure so that it does not come off during the drying cycle. A new dryer clip might be needed if the front panel of the dryer is off balance or not attached correctly. It is possible that the clips can become loose over time as the appliance is prone to shaking and vibrating. The clips are important as it keeps the dangerous parts covered. If the entire front panel can be lifted off then it is time to replace the dryer clips. These clips are sold individually even though dryers typically have more than one. This clip is a genuine OEM part.

This retaining clamp secures wiring, hoses, or small assemblies to keep them routed and stable, helping prevent rubbing and vibration that can lead to wear or intermittent issues. Use it to replace a broken or missing clamp. What it does:

• Holds wires, hoses, or tubing in place to prevent contact with moving parts
• Reduces vibration and rattling by keeping components secure
• Prevents chafing that can cause insulation wear or exposed wiring
• Restores proper routing after repairs or part replacement

• Disconnect power (and water if applicable) before accessing internal components
• Use appropriate hand tools; avoid over-tightening which can damage the clamp or secured part
• Inspect surrounding wiring/hoses for damage and replace if needed

This clamp is a small retaining fastener used to secure hoses, tubes or wiring to appliance fittings and keep connections stable during operation. It helps prevent leaks, chafing and loose connections that can cause performance issues. What it does:

• Secures a hose or tube to a barb or fitting to maintain a tight seal
• Prevents hoses and lines from slipping free during use or vibration
• Reduces wear from rubbing or chafing by holding components in place
• Helps stop minor leaks at hose junctions when properly seated

• One clamp (quantity: 1)

• Disconnect power and water supply before servicing the appliance
• Drain or catch any residual water from hoses before removing the old clamp
• Use the correct pliers or screwdriver for the clamp type; avoid over-tightening which can damage hoses
• Inspect adjacent hoses and fittings and replace any worn components while accessible

This dryer hose clip secures the exhaust hose to the dryer's cabinet for a stable, sealed connection. A small but essential fastener, it helps keep the vent attached so airflow is directed out of the appliance. What it does

• Fastens the exhaust/vent hose to the dryer cabinet to maintain a secure connection.
• Helps reduce air leaks at the hose-to-cabinet joint that can cause reduced venting efficiency.
• Prevents the hose from slipping off during operation, which can cause vibration or rattling.
• Keeps the vent path aligned to reduce lint buildup at the connection point.

• One dryer hose clip.

• Disconnect power (unplug electric or shut off gas and unplug) before servicing the dryer.
• Remove the dryer vent hose and position the clip over the hose and cabinet fitting; secure per OEM orientation.
• Tighten only to snug — avoid over-tightening which can deform the hose or cabinet inlet.
• Inspect the hose and cabinet inlet for damage; replace damaged components to ensure a proper seal.