General Electric Washer Dryer Combo Spring Parts

This shifter spring helps engage and return the transmission shifter mechanism in select top-load washers, allowing smooth changes between agitation and spin for reliable wash performance.

• Maintains proper tension on the shift mechanism between agitate and spin
• A worn or broken spring can cause no spin, no agitate, or loud shifting noises
• May also lead to intermittent shifting or incomplete cycles
• Restores consistent mechanical engagement of the drive system

• Unplug the washer and shut off water supply before servicing
• Access is typically from the cabinet/rear; support the tub to prevent movement
• Note spring orientation and attachment points before removal
• Use needle-nose pliers or a spring tool; replace any severely worn mating parts

This front suspension rod assembly supports and stabilizes the washer tub from the front side, helping control vibration and keeping the basket centered for smooth spin and wash performance.

• Supports the tub from the front to maintain proper alignment
• Helps reduce excessive vibration, banging, or walking during spin
• Can address shaking, out-of-balance loads, or tub leaning forward
• Restores proper suspension when the original rod or spring is worn or broken

• Unplug the washer and shut off water before servicing
• Access typically requires lifting the top or removing the cabinet/front panel
• Support the tub while swapping the rod to prevent sudden drop
• Replace in matched positions; inspect other suspension rods for wear

This rear suspension rod assembly supports the washer tub from the back of the cabinet. Replacing a worn or broken rod restores stable spin performance and helps reduce banging, vibration, and off-balance interruptions.

• Supports and stabilizes the wash tub from the rear of the cabinet
• Absorbs tub movement during agitation and spin to minimize vibration and noise
• Helps maintain tub alignment to reduce off-balance pauses or repeated redistributions
• Typical symptoms include loud banging, excessive shaking/walking, or the tub leaning toward the back

• Disconnect power and water; wear gloves and eye protection
• Open the cabinet or raise the top to access the rear suspension
• Support the tub to relieve tension, then remove and replace the rod in the same mounting points
• Level the washer and run a short test cycle after replacement

This spring cover protects and retains a mechanism spring inside your washer. Replacing a cracked or missing cover helps keep the spring seated, limits debris intrusion, and supports smooth, reliable movement of the associated control, latch, or linkage.

• Shields the spring and helps keep it properly seated in its pocket
• Reduces friction and wear that can lead to premature spring failure
• Supports consistent return action for the related control, latch, or lever
• Typical symptoms include a missing/broken cover, exposed spring, rattling, or erratic operation

• Unplug the appliance and turn off water before servicing
• Access point varies by model; photograph spring/cover orientation before removal
• Control the spring during disassembly to prevent sudden release
• Ensure the cover is fully seated; test operation before final reassembly

This short vertical spring provides the tension needed for the appliance's vertical hinge or mounting assembly, restoring proper movement and alignment for smooth operation and secure closure. What it does:

• Supplies vertical tension to a hinge or mounting assembly to maintain proper positioning
• Helps restore even, controlled movement of doors, panels or drawers
• Reduces sagging, slipping or uneven closing caused by a worn spring
• Minimizes rattling or misalignment during normal use

• Disconnect power to the appliance before beginning any repair.
• Springs can be under tension — wear safety glasses and use appropriate tools.
• Inspect mating hardware (clips, pins, brackets) for wear and replace if needed.

This rear rod assembly supports and stabilizes the dryer drum so it spins smoothly and stays aligned. Replacing a worn or bent rear rod restores proper drum tracking and reduces rubbing, noise, and vibration. What it does

• Provides a mounting/axle point at the back of the drum to keep rotation centered
• Helps prevent drum wobble, scraping noises, and uneven wear on drum seals or glides
• Commonly replaced when the drum is hard to turn, noisy, or visibly misaligned
• Works with existing rollers, bearings, and retaining hardware to maintain drum stability

• One rear rod assembly as shown

• Disconnect power (and gas if applicable) before beginning any repairs
• Access typically requires removing the dryer cabinet or back panel and the drum — follow the OEM service manual
• Inspect related rollers, bearings, and seals and replace if worn to avoid repeat failure

This suspension spring supports the washer tub and helps stabilize the drum during cycles, reducing excessive movement and vibration for smoother operation. It restores proper tub positioning and helps prevent noisy, off-balance spins. What it does:

• Cushions and centers the washer tub to limit excessive vibration and shaking during spin cycles
• Helps maintain correct tub alignment for smoother, quieter operation
• Can reduce symptoms such as loud banging, rocking, or uneven spinning
• Works with the washer's suspension system to protect other components from stress

• One washer suspension spring

• Disconnect power and water supply before servicing
• Support the tub or cabinet while removing/installing the spring to prevent sudden movement
• Inspect other suspension components (shocks, mounts, springs) and replace as needed for best results