Gibson Range Parts

The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt

Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.

Symptoms of a bad Surface Element include:

• Not heating up, indicating it may be burnt out or disconnected.
• Heating irregularly or only partially, suggesting there might be damage to the element.
• Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This broil element mounts at the top of the oven cavity and delivers radiant heat for broiling and top-browning. Replace a broken or burned-out element to restore consistent broil performance.

• Emits high, radiant heat from the top of the oven during the broil cycle
• Used to sear and top-brown foods
• Replaces the original broil element on compatible units
• Common symptoms: No heat in broil, element won't glow, uneven top browning, visible cracks/blistering on the element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; support the element while removing mounting screws
• Carefully pull the element forward and disconnect the wire terminals; avoid bending the element
• Attach the new element, secure with screws, ensure it is clear of the oven liner, then restore power and test

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Door Trim Kit restores the finished look and proper fit around the door. It replaces damaged or missing trim that frames the door/panel, helping secure outer components and refresh the appliance's appearance.

• Provides a clean, finished edge around the door perimeter
• Helps retain/position the outer glass or panel on applicable designs
• Replaces cracked, warped, loose, or missing trim that may rattle or leave gaps
• Common symptoms: visible damage, looseness, gaps, or cosmetic wear around the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Protect the work surface; wear cut-resistant gloves and handle glass carefully
• Note orientation and fastener locations; transfer any reusable clips/screws from the original assembly
• After reassembly, confirm smooth door operation and proper alignment/seal

This surface burner mounts on the cooktop and directs gas to produce a steady, controllable flame. Replace a worn or clogged burner to restore fast ignition and consistent heat from your range's top burner positions.

• Mixes and distributes gas to create the surface cooking flame
• Works with the spark igniter/electrode for reliable lighting
• Helps maintain an even flame pattern and stable heat
• Symptoms can include weak or uneven flames, yellow tips, delayed ignition/repeated clicking, or a burner that won't light

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap, then lift off the old burner; clean the mounting surface
• Align the new burner with the igniter/electrode and locator features; ensure it sits flat and centered
• Reassemble, restore gas/power, and test for proper ignition and a clean, stable flame

The Door Handle Kit is an OEM replacement part for Frigidaire ovens and ranges. These handles provide safe access to the oven interior.

Causes of a bad handle kit can include normal wear over time of moving parts, accidental damage from impact or mishandling of the oven door, or issues with the latching mechanism.

Symptoms of a bad oven door handle kit include:

• Loose, sluggish, or difficult operation of handles
• Handles detaching from oven door
• Inability to fully open or close the oven door
• Problems with door sealing or staying closed securely

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is the factory handle set for select Frigidaire-built appliances. It restores a secure, comfortable grip and fresh appearance so doors or drawers open and close as intended. What it does

• Provides the handhold needed to open and close the appliance door or drawer
• Replaces cracked, broken, or missing handles
• Helps correct loose or wobbly handles that won't stay tight
• Refreshes worn or scuffed handles for a cleaner look

• Manufacturer-supplied handle set

• Disconnect power before servicing; allow hot surfaces to cool
• Remove interior/hidden mounting screws and the old handle
• Align and secure the new handle; re-use existing hardware/brackets if applicable
• Do not overtighten fasteners; verify smooth door/drawer operation

This handle mounting screw secures an appliance handle, most commonly the oven door handle, to the door or front panel. Replacing a worn, stripped, or missing screw restores a firm grip and keeps the handle aligned and secure.

• Secures the handle to the door or trim as designed
• Replaces stripped, rusted, or missing hardware
• Helps correct a loose or wobbly handle
• Reduces rattling or misaligned trim caused by a missing fastener

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the handle and door/front panel during removal and installation
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten until snug—do not overtighten

Color: white. It measures about 1-3/4 inches in diameter.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This factory wire harness routes electrical power and signals between the controls and internal components of your cooking appliance. Replacing a burned or brittle harness restores safe, reliable connections and helps prevent shorts or intermittent operation.

• Distributes power and control signals between the user interface/control system and internal components
• Replaces damaged wires or connectors that can cause no operation or intermittent function
• Helps address short-to-ground conditions that trip a household breaker
• Restores proper routing to reduce wire chafing and heat exposure

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph/label connections and transfer one connector at a time to match original locations
• Route along factory paths and secure with existing clips/ties; keep clear of sharp edges and hot surfaces
• Inspect mating terminals for heat damage and repair/replace affected parts before reassembly

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

Length - 7.53"

This oven insulation surrounds the oven cavity to retain heat and protect nearby components and cabinetry. Replacing a burnt or deteriorated insulation blanket restores temperature stability and helps keep exterior surfaces cooler on your range during cooking.

• Minimizes heat loss for more consistent baking temperatures
• Shields wiring, controls, and adjacent cabinets from excessive heat
• Damaged insulation can cause long preheat times or trouble maintaining set temperature
• Exterior panels or control area may feel unusually hot, or a burnt odor may persist after spills

• Disconnect power at the breaker; shut off gas
• Allow the appliance to cool completely before service
• Access typically requires pulling the range and removing outer panels; note original routing and retainers for reassembly
• Handle insulation carefully; wear gloves, eye protection, and a dust mask to avoid irritation from fibers

This machine screw adjusts and secures the leveling leg or bracket, helping you set the appliance stable and plumb. Replacing a stripped, bent, or missing screw restores a solid footing and makes accurate leveling possible.

• Threads into the base or leveling bracket to raise or lower the appliance for proper leveling
• Helps reduce rocking, wobbling, and vibration from an unlevel installation
• Common signs of wear: stripped threads, bent hardware, corrosion, or a missing screw
• Useful during installation or when the existing adjustment screw no longer holds

• Disconnect power; shut off gas before working
• Support the appliance to relieve weight on the leveling point
• Remove the damaged screw; inspect and clean mating threads
• Start the new screw by hand to avoid cross-threading, then adjust height and snug