Gibson Refrigerator Parts

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

This ice dispenser lever is the actuator you press with your glass to release ice from the freezer door. A worn or broken lever can keep the door dispenser from dispensing ice or make it hard to activate.

• Transfers your push at the dispenser pad to the ice dispenser switch
• Helps restore normal ice dispensing from the door chute
• Common symptoms: lever broken, loose, or stuck; no ice dispensed when pressed
• May cause intermittent dispensing if the actuator is worn or misaligned

• Unplug refrigerator before service; wear cut-resistant gloves
• Remove dispenser trim and control panel as needed to access the lever
• Note spring and pivot orientation; transfer any reusable hardware
• Test dispenser operation before reinstalling trim

The Cold Control is an OEM part for Frigidaire refrigerators. This component regulates the temperature inside the refrigerator by controlling the operation of the compressor and the flow of refrigerant. It ensures that the interior remains at the desired temperature to keep food fresh. This temperature control thermostat features a 16" capillary tube. 

Over time, the cold control can become faulty due to regular wear and tear, electrical issues, or exposure to moisture. A malfunctioning cold control can result in temperature fluctuations and ineffective cooling.

Symptoms of a bad cold control include:

• The refrigerator not maintaining the correct temperature
• The compressor running continuously or not at all
• Frost buildup in the freezer compartment
• The refrigerator being too warm or too cold

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Kit includes ice and water actuator arms.

The Dispenser Module Cover is an OEM part for Frigidaire Refrigerator. It is the decorative plastic shroud that fits externally over the ice and water dispenser components.

Causes can be normal wear from frequent use of the dispenser, impacts from children or pets pressing on the area, or damage from attempted cleaning with improper chemicals over time.

Symptoms of a bad dispenser module cover include:

• Cracked, faded or stained external appearance
• Exposed wires and components vulnerable to liquid intrusion
• Cover not properly sitting flush or securely clipping into place

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

This evaporator fan motor mounting bushing isolates the motor from its bracket to reduce vibration and rattling. Replacing a worn bushing helps keep the fan secure and centered so airflow remains smooth and operation is quieter. What it does:

• Cushions and isolates the evaporator fan motor to reduce vibration and noise
• Helps maintain motor alignment to prevent the fan blade from rubbing the shroud
• Secures the motor to the mounting bracket
• Typical symptoms: rattling or buzzing from the freezer, fan wobble, loose motor, or a cracked/missing bushing

• One motor mounting bushing

• Unplug the refrigerator before servicing and wear safety gloves
• Remove the freezer back panel/evaporator cover to access the fan motor
• Support the motor, remove fasteners, and transfer/install the bushing on the bracket/motor as shown in your service diagram
• Ensure the bushing is fully seated and the fan blade spins freely with proper clearance before reassembly

This door-activated light switch controls the interior lamp in your refrigerator. Replace a worn or sticking switch to restore dependable lighting and prevent the bulb from staying on and warming the compartment when the door is closed.

• Opens and closes the light circuit as the door is opened and closed
• Helps prevent the light from staying on with the door shut
• Common symptoms: interior light won't turn on, stays on with the door closed, or works intermittently
• Physical signs may include a stuck/broken plunger or damaged housing

• Disconnect power before servicing
• Gently pry the old switch from the liner/panel and release its locking tabs
• Transfer wires one at a time to the same terminals on the new switch
• Press the new switch fully into place; restore power, and test

Color: White. Used to cover the hinge bearing hole.

This position-specific ice crusher blade (#1) fits inside the refrigerator's ice bucket assembly. It helps break up cubes into crushed ice; replacing a bent or worn blade restores consistent crushing and reduces jams or grinding noises during dispensing.

• Works with the auger and other numbered blades to crush ice when "Crush" is selected
• A bent, dull, or corroded blade can lead to no crushed ice, only cubes, slow dispensing, or scraping/grinding noises
• Restores even crushing and smoother auger rotation
• Position- and orientation-specific within the blade stack; match to your original

• Disconnect power and switch the ice maker OFF before servicing
• Remove and empty the ice bucket; allow any frost to thaw
• Disassemble the bucket front/auger and note the exact blade order and orientation—take photos for reference
• Wear cut-resistant gloves; reassemble blades, spacers, and washers exactly as removed and verify the auger turns freely before reinstalling

This defrost heater kit restores the automatic defrost cycle by melting frost from the freezer's evaporator coils. Replacing a failed heater helps clear ice buildup, restore airflow, and stabilize temperatures for reliable cooling performance.

• Heats the evaporator during defrost to remove frost and ice
• Helps maintain proper airflow through the coils for consistent cooling
• Common symptoms of a failed heater: heavy frost on the back freezer wall, weak airflow, warming temps, or cooling that improves after a manual defrost
• Supports efficient operation by preventing ice from re-forming on the evaporator

• Unplug the refrigerator before servicing; let any sharp parts or coils warm up to avoid damage
• Access the heater behind the freezer's rear panel; handle the element carefully to avoid damage
• Note wire routing and mounting before removal to match the original configuration
• Check the defrost thermostat and defrost control/timer for proper operation

The Frigidaire Refrigerator Water Filter Cover is an OEM part for Frigidaire refrigerators. It serves as a protective casing for the water filter, ensuring it is shielded from damage and securely in place within the appliance. This cover helps maintain the aesthetic integrity of the interior of your refrigerator while also providing easy access for filter changes.

Causes of a bad water filter cover can include physical damage such as cracks or breaks, which may occur from accidental impacts or during the filter replacement process.  

Symptoms of a bad Water Filter Cover include:

• Difficulty in accessing or replacing the water filter
• Loose fit that can lead to vibration or noise
• Visible damage like cracks or warping

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This auger motor powers the ice dispenser, rotating the ice-bin auger to feed cubes or crushed ice to the door chute. A failed motor stops dispensing, leaving ice in the bucket when the paddle or lever is pressed.

• Drives the auger that moves ice from the bin to the dispenser chute
• Restores dispensing when the original motor is seized or burned out
• Common symptoms: no ice through the door, auger doesn't turn, motor only hums or clicks
• Note: Won't resolve issues from a jammed auger, frozen ice bucket, or broken drive parts

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the ice bin to access the motor area as designed on your model
• Note wire orientation; transfer any reusable brackets or hardware from the original motor
• Align the drive interface and secure; test both cube and crush functions before reassembly

This drain hose carries water away from your appliance during draining to help prevent backups and leaks. Replace a cracked, clogged, or kinked hose to restore reliable water removal and protect surrounding floors and cabinets. What it does:

• Directs drain water from the outlet or pump to the designated discharge point
• Maintains proper flow; kinks or blockages can cause slow or no draining
• Helps prevent leaks from splits, pinholes, or loose connections
• Common signs: standing water, water under/around the unit, drain-related error codes, or odors

• Includes 1 drain hose

• Disconnect power and shut off water supply before servicing
• Place towels or a shallow pan to catch residual water when removing the old hose
• Note the original routing; seat connections fully, secure with clamps, and avoid sharp bends or kinks
• Run a brief drain/rinse and check all joints for leaks

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation