Gibson Refrigerator Parts

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

This replacement glass insert fits into the crisper cover frame to create a sturdy, easy to clean surface above your produce drawers. Replace a cracked or missing insert to restore safe storage and proper drawer support.

• Sits in the crisper cover frame to support items above the drawers
• Helps contain spills to protect the drawers below
• Maintains correct spacing so crisper drawers open and close smoothly
• Replace when the original glass is cracked, chipped, shattered, or missing

• Unload the shelf and remove the crisper drawers
• Lift out the crisper cover frame and place it on a flat surface
• Remove the damaged glass and set the new insert into the frame recess without forcing
• Reinstall the cover and drawers; wear cut-resistant gloves and handle glass carefully

This sliding shelf frame supports the refrigerator's shelf glass and allows the shelf to pull out for easier access to food. Replacing a cracked or warped frame restores a stable, level surface and smooth shelf movement.

• Supports the shelf glass and food load to keep items level and secure
• Enables slide-out access; helps the shelf move smoothly on its side supports
• Restores stability when the original frame is cracked, warped, or has broken support points
• Can help with issues like a shelf that sags, binds, or won't sit correctly

• Disconnect power and remove items from the shelf area before service
• Carefully lift out the shelf assembly; remove and set aside the glass insert
• Transfer any inserts/trim (such as the glass panel) to the new frame if your model uses them
• Seat the new frame on the side supports and verify smooth sliding action

This genuine OEM part is a temperature control thermostat for refrigerators. The temperature control thermostat is the part that regulates and adjusts the temperature settings of the refrigerator. If the refrigerator is no longer maintaining the desired temperature settings, not cooling, or otherwise not operating properly, it will need to be replaced. To replace this part, make sure the refrigerator is unplugged. After unplugging, proceed to open the refrigerator door and remove all the interior shelving. Once removed, proceed to unmount the screws that hold the interior panels in place. Once loosened, remove the panels to access the temperature control thermostat. After locating the part, unthread the mounting screws that secure the thermostat to its housing. After unthreading, pull the old thermostat out and remove the wire harness that it is attached to. Replace it with the new thermostat and proceed to reinstall the interior panels of the refrigerator. This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

This defrost heater warms the evaporator coil during the automatic defrost cycle to melt frost and ice, restoring airflow and consistent temperatures. Replace a failed heater to stop recurring frost buildup and uneven cooling. What it does:

• Heats the evaporator to clear frost/ice so air can circulate
• Helps maintain stable refrigerator and freezer temperatures
• Symptoms include heavy frost on the back freezer panel or coils, poor cooling, evaporator fan noise from ice contact, or frost returning soon after a manual defrost

• 1 defrost heater

• Disconnect power before servicing
• Remove freezer shelves and the rear interior panel to access the evaporator area
• Transfer the heater into the original clips/brackets and route wiring exactly as original, away from sharp edges and the fan
• If frost returns after replacement, also test the defrost thermostat and the defrost control

• With power disconnected, the heater should show continuity on an ohmmeter; an open circuit indicates a failed element

This damper control knob fits the refrigerator's air damper. It attaches to the damper control so you can open or close airflow between the freezer and fresh food compartments when the original knob is cracked, stripped, or missing.

• Attaches to the damper control shaft to adjust airflow from the freezer into the refrigerator compartment
• Direct replacement for a knob that is broken, missing, or stripped
• Symptoms can include a loose or slipping control, difficulty turning, or settings that won't stay in place
• If the control can't be turned, temperature response to damper adjustments may be inconsistent

• Disconnect power to the refrigerator before servicing
• Pull the old knob straight off the control shaft; avoid prying to prevent damage
• Align the new knob with the shaft and press it on until fully seated
• Rotate through the full range to ensure smooth operation without forcing

The Switch-4 Button Assembly is an OEM part for Frigidaire refrigerators. This switch assembly operates important refrigerator functions like the light controls, temperature selection, and ice/water dispenser functions. It contains four precise switches designed to last through years of use while maintaining accurate input control.

Causes of a bad switch assembly can include continuous actuations over time leading to switch wear, accidental damage or spills compromising switch integrity, or failures in electronic components.

Symptoms of a bad switch assembly include:

• Lights or temperature settings not functioning properly
• Ice/water dispenser buttons not working as expected
• Failed or improperly actuating switches
• Water leaks or electrical issues at the switch location

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator replacement icemaker includes the cover, fill cup, bail arm and a four pin plug harness.

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This sliding full-width shelf frame supports the refrigerator's glass shelf and lets it pull out for easier access. Replace a cracked or warped frame to restore stable storage and smooth shelf movement in the fresh food compartment. What it does:

• Holds the glass shelf insert across the full cabinet width
• Provides slide-out action for easier loading and unloading
• Helps keep the shelf level and secure under normal food weight
• Common signs it's failing: cracked/broken corners, shelf won't slide smoothly, sagging or tilting, glass feels loose

• One sliding shelf frame

• Empty the shelf; remove and set aside the glass insert before replacing the frame
• Handle glass carefully and wear cut-resistant gloves
• Seat the new frame on the shelf supports; ensure all tabs are fully engaged
• Reinstall the glass and confirm smooth sliding before reloading items

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This small clip secures the crisper cover's slide so it stays aligned and operates smoothly. Replacing a broken or missing clip restores proper slide action and helps keep your crisper cover assembly functioning as designed.

• Holds the crisper cover slide in place and aligned with its track
• Helps the slide move smoothly without popping off or binding
• Common symptoms: slide is loose or falls out, won't stay in place, cracked/missing clip
• Visual damage or loss can leave the crisper drawer cover slide inoperable

• Disconnect power and remove food items for safe access
• Remove the crisper drawer and lift out the crisper cover assembly
• Release the damaged clip and snap the new clip into the cover/slide as oriented
• Reassemble and verify the slide moves freely end to end

This door hinge bearing fits the refrigerator door hinge and provides a smooth, low-friction pivot point. Replacing a worn bearing restores smoother door movement and helps maintain proper alignment and a reliable gasket seal. What it does:

• Provides a low-friction surface between the hinge pin and door
• Helps keep the door aligned for consistent gasket contact
• Reduces squeaks, scraping, or binding during opening and closing
• Helps with symptoms like door sagging, not closing fully, or uneven sealing

• 1 hinge bearing

• Disconnect power and remove items from the door before servicing
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Replace the bearing in the same orientation; reassemble hardware securely
• Reinstall the door and ensure smooth swing and full gasket contact around the perimeter

Used on fresh food and freezer doors.