Hardwick Range / Cooktop / Oven Parts

This thermostat monitors temperature in the appliance's heating circuit and opens or closes the electrical contacts to control heat and protect against overheating. Replacing a failed thermostat restores consistent heating performance and reliable safety shutoff. What it does:

• Senses temperature and cycles the heating circuit on and off to maintain target heat
• Provides over-temperature protection by opening the circuit if conditions exceed safe limits
• Helps prevent nuisance shutdowns caused by erratic temperature readings
• Common failure symptoms include no heat, inaccurate temperatures, short-cycling, or shutdown during high heat

• 1 thermostat

• Disconnect power (and gas supply if applicable) before servicing; allow all components to cool completely
• Access the thermostat per your service manual; document wire locations and transfer one at a time
• Mount the thermostat securely so the sensing surface/bulb is correctly positioned; avoid kinking or pinching any leads
• After installation, verify proper operation and temperature performance

Replacement control knob for the oven thermostat. It installs on the thermostat shaft so you can select cooking temperatures. Replaces a cracked, loose, or missing knob to restore smooth adjustment and clear, readable settings. What it does:

• Provides the hand control to turn the oven's thermostat and set temperature
• Press-fits onto the thermostat shaft for consistent, aligned operation
• Restores a secure grip and pointer alignment when the original is worn
• Common symptoms: knob cracked, falls off, spins freely, or markings are hard to read

• One white thermostat control knob

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Pull the old knob straight off the thermostat shaft—avoid prying against the panel
• Align the new knob with the shaft flat and press straight on until fully seated
• The pointer aligns with Off; remove and reseat if needed

Bottom-mounted bake element that provides the primary heat for baking. Replace when burned out or damaged to restore proper preheat and even baking.

• Supplies radiant heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common failure signs: no heat in bake, slow preheat, uneven results, or visible cracks/blistering on the element
• A shorted element may trip the household circuit breaker when Bake is selected

• Disconnect power at the breaker or unplug; allow the oven to cool completely
• Remove racks; take out the element's mounting screws, gently pull it forward, and move the two wires to the new element one at a time using insulated pliers
• Don't let wires slip back through the rear panel; inspect terminals for heat damage, reassemble, restore power, and test preheat

This surface burner knob fits the valve stem for a cooktop/range burner control. It restores a secure grip and accurate adjustment when the original knob is cracked, stripped, loose, or missing.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame level
• Replaces a knob that slips, won't stay on, cracks, melts, or free-spins
• Helps restore proper Off alignment and a clean, finished look

• Ensure all controls are in the Off position; disconnect power and shut off gas as a safety precaution
• Pull the old knob straight off the valve stem—do not pry sideways
• Align the flat/D-shaped opening with the valve stem and press firmly until fully seated
• Verify smooth operation and correct Off alignment before restoring power/gas

Color: black. It measures about 2 inches in diameter.

This door handle spacer fits between the handle and the door panel, providing the correct standoff and a clean, finished look. Replacing a worn spacer helps keep the handle secure and aligned.

• Maintains proper spacing between the handle and door surface
• Helps stabilize a loose or wobbly handle
• Replaces cracked, discolored, or missing spacers
• Color: Bisque (cream/tan finish) to match compatible appliances

• Disconnect power and allow the appliance to cool before servicing
• Support the door and handle while removing mounting screws
• Transfer or replace spacers on both sides of the handle if needed; do not overtighten screws
• Wear gloves to protect hands and avoid stressing glass panels

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This is a replacement broil element for the oven's upper heating function. It restores high-heat broiling and top-surface browning so you can sear, brown, and finish foods as intended. What it does:

• Produces the direct, high heat required for broiling and browning
• Replaces a burned-out, visibly damaged, or non-heating upper element
• Restores even top-heat for recipes that require searing or finishing
• Helps eliminate weak or no heat from the oven's broil function

• One broil element

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and use basic hand tools to remove mounting screws and the old element
• Handle the new element carefully to avoid bending or damaging terminals

This is a set of eight replacement control knobs designed to restore function and appearance to compatible Whirlpool appliances. The kit gives you matching knobs to operate controls and replace cracked, faded, or missing pieces. What it does:

• Replaces worn, cracked, or missing control knobs so you can reliably set cycles, temperatures, or power levels
• Restores a uniform look across the appliance control panel
• Provides a direct-fit replacement for appliances that use the 8-knob kit
• Helps improve grip and control when turning settings

• Remove old knobs by pulling straight off the splined shaft; align new knob spline and push onto the shaft until fully seated
• No special tools typically required; use gentle force to avoid damaging the shaft
• If knobs control electrical functions, ensure appliance controls are off before replacing; disconnect power or gas if advised by the appliance manual

Replace a damaged or unsteady cooking surface with this burner grate. It supports pots and pans at the proper height above the burner, restoring stable, level support on your gas cooktop or range when the original grate is worn or broken.

• Provides sturdy support for cookware over the surface burner
• Maintains the correct clearance between burner and pan for consistent heating
• Replaces grates that are cracked, bent/warped, or have worn feet causing wobble
• Helps prevent rocking or instability of pots and pans during cooking

• Allow the cooktop/range and grate to cool completely before handling
• Lift off the old grate; clean the surface; align and place the new grate over the correct burner
• Ensure the grate sits flat and stable—do not force into place
• Refer to your owner's manual for care and cleaning recommendations

A genuine replacement screw used to secure components on compatible Whirlpool appliances. This small fastener restores proper assembly and helps stop loose panels, trim, or internal parts from rattling or shifting during operation. What it does:

• Secures panels, brackets, or components to restore proper fit and reduce vibration noise
• Replaces missing or stripped fasteners that cause parts to sit unevenly or move during cycles
• Helps maintain safe, stable appliance operation by keeping components fastened

• Use the matching screwdriver or bit to avoid stripping the head; do not force a damaged screw
• Hand-start threads before using a driver to prevent cross-threading
• Replace any additional corroded or damaged screws with matching fasteners for best fit
• Disconnect power and follow appliance-specific safety steps before accessing internal parts

This replacement light lens covers the appliance's bulb, protecting it from contact, moisture, and splashes while diffusing illumination. Replacing a cracked or missing lens restores safe, even lighting and keeps the bulb properly shielded. What it does:

• Shields the bulb from contact, moisture, and debris
• Diffuses light for more even illumination with reduced glare
• Helps protect the socket area from contamination
• Typical symptoms: cracked, warped, or missing lens; discoloration; exposed bulb; harsh or uneven lighting

• Includes: 1 light lens

• Disconnect power to the appliance before servicing; allow the lamp/area to cool completely
• Wear gloves and eye protection when handling an old or broken lens
• Remove retaining screws, tabs, or clips and note lens orientation for reassembly
• Reuse existing hardware if required; do not overtighten; restore power and test light operation