Hardwick Range Parts

Oven won't reach temperature or overheats? This thermostat monitors heating circuits and controls temperature. Moderate difficulty repair, requires back access.

Replace a cracked, stripped, or worn thermostat knob on your electric range. This control knob attaches to the thermostat stem for temperature adjustment.

Fix an oven that won't heat or bakes unevenly with a new bake element. This bottom heating element restores proper preheating and even baking temperatures.

Color: black. It measures about 2 inches in diameter.

Replace a cracked, stripped, loose, or missing surface burner control knob on your range. Attaches to the valve stem to restore secure grip and control.

Bisque spacer that installs between range door handle and panel. Replace if cracked, broken, or missing to restore proper spacing and secure alignment.

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your electric range. Simple plug-in replacement.

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This is a set of eight replacement control knobs designed to restore function and appearance to compatible Whirlpool appliances. The kit gives you matching knobs to operate controls and replace cracked, faded, or missing pieces. What it does:

• Replaces worn, cracked, or missing control knobs so you can reliably set cycles, temperatures, or power levels
• Restores a uniform look across the appliance control panel
• Provides a direct-fit replacement for appliances that use the 8-knob kit
• Helps improve grip and control when turning settings

• Remove old knobs by pulling straight off the splined shaft; align new knob spline and push onto the shaft until fully seated
• No special tools typically required; use gentle force to avoid damaging the shaft
• If knobs control electrical functions, ensure appliance controls are off before replacing; disconnect power or gas if advised by the appliance manual

Replace a cracked, worn, or broken burner grate on your gas range or cooktop. This grate supports cookware over the burner for stable, level cooking.

Burner won't ignite or control knob is hard to turn? This top burner valve controls gas flow to surface burners. Moderate DIY repair with basic tools.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or damaged.

Protects the bulb from moisture and contact while diffusing light. Replace when cracked or missing to restore safe, even oven lighting. Confirm fit.

This shaft-bit generator is a replacement drive shaft component that transfers motor rotation to the appliance's moving assemblies, restoring proper mechanical motion and reducing noise from damaged or worn shaft parts. What it does:

• Transfers rotary motion from the motor to the driven components for normal operation
• Helps maintain alignment and smooth rotation of connected parts
• Worn or broken units can cause grinding, rattling, or loss of movement
• Replacing a failed shaft can stop intermittent operation and restore reliable performance

• High-level replacement only: remove power before accessing internal assemblies
• Follow appliance-specific disassembly steps; secure panels and wiring before removing the old shaft
• Inspect adjacent bearings, seals, and mounting hardware; replace any damaged items