Hedge Trimmer Spring Parts

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

The chainsaw isolator kit is a spring mechanism that is designed to help reduce vibrations in the equipment while it is being used. Reducing vibrations makes the equipment more enjoyable to use and protects it from additional damage that could occur. This assembly can become worn over time, which will lead to increased vibrations and less stable use of the chainsaw. Replacing the isolator with this kit can alleviate the issues and provide a solution for many common issues. This genuine OEM isolator kit is manufactured by Poulan to exact standards so that it provides an exact fit for compatible models of chainsaws. It can be used with hundreds of chainsaws from Poulan, Jonsered, and Husqvarna. Refer to model diagrams for appropriate installation, placement, and part compatibility information. This is an individual part that is sold as a single unit. This isolator assembly includes all the parts needed for a full replacement: one bolt, two springs, and one isolator with a bar that includes two bolts for mounting. No additional parts or hardware will be required to go with this part replacement.

Many gas-powered small engines require the use of a pull cord to get the engine going. Rather than a starter, it is the pull of the cord that causes the engine to turn over and combustion to begin inside of the engine. These pull mechanisms often use a damper spring on the starter assembly. It exists to "pre-load" a recoil or pull starter with a lot of tension. When it malfunctions, it will take a tremendous amount of effort to get the engine going. This replacement damper spring is designed for a long list of Shindaiwa and Echo machines. These include trimmers, blowers, edgers, and more. This OEM replacement part is shipped individually and made of durable metal for years of service.

This spring is a genuine Echo part, sold individually. This spring can be used as a replacement part for string trimmers. In a string trimmer, the function of the spring is to maintain the placement of the components to which it is linked through the use of spring tension. Damage to a spring can be very dangerous for appliances due to the amount of tension that springs are placed under. If there is damage to a spring that loosens its tension, it should immediately be removed and replaced by this genuine OEM replacement part before using the string trimmer again. This damage can come in the form of general wear and tear from exposure or aging, or as a result of a collision with a falling or a hard object that can warp the spring beyond functionality. Remember to wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This spring is compatible with the following outdoor appliance brands: Echo and Shindaiwa.

This replacement driver spring is a genuine OEM part for a string trimmer with a starter rope ignition. When an operator pulls the starter rope, the rope must recoil back into the starter assembly before it can be used again. This spring connects to a driver pulley in the starter assembly and maintains the right amount of tension needed to recoil the pulley. Over time, driver springs will begin to lose some of their tension. This is especially true if the operator is quite rough on their appliance. Pulling too hard on the starter rope can wear out the spring more quickly, making it less effective. Without a properly tensed driver spring, the starter rope will not recoil into the assembly. To change out the spring, use a nut driver to open the starter assembly and remove the pulley to get access to the old spring. Carefully remove it and install the new part. This replacement driver spring is a high-quality part designed to match the exact specifications for a Husqvarna or Jonsered appliance. This part is sourced from its original manufacturer and ships individually.

A throttle return spring is a coil-shaped metal mechanism designed for use with outdoor lawn and garden power equipment such as trimmers, hedge trimmers, tillers, string trimmers, pole pruners, cultivators, pumps, reciprocating saws, regular saws, edgers, leaf blowers and vacuums, and pole saws. It is compatible for use with products manufactured by Echo, Mantis, Little Wonder, and Shindaiwa.The throttle return spring pushes the throttle closed when the user lets off the gas. A weak or failed throttle return spring is dangerous because it will prevent the throttle from easily returning to its resting position. This could pose a serious safety hazard to the person operating the machine and anyone nearby. This throttle return spring is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. It is manufactured by Echo. This throttle return spring is made of metal.

A lever spring is a part of a trimer or tiller that works with the lockout lever. The lockout lever needs to be depressed before the throttle can activate. The return spring is responsible for offering tension so the lockout lever works the way it should. As time goes on, the spring can start to break down or even fall apart. Visually inspecting the part will give information about whether a replacement is needed.The first step is removing the lever return spring by taking off the control handle assembly and then getting to the lever spring so it can be taken out. Once it has been removed from the lockout lever, the new lever spring can be installed. It will be slid over the mounting post on the mounting handle where the straight part of the spring faces down. Take the straight end of the spring between the retaining clip and outside wall on the handle. Install the lockout lever while sliding it over the mounting post. This metal lever spring is sold individually. It is a genuine OEM replacement part directly sourced from the manufacturer. It is designed for use with tillers, hedge trimmers, and string trimmers by Echo and Mantis.