Hotpoint Dishwasher Switch
Genuine Ge part
By: Ge
Part Number: WD21X25468
Fix H2O error codes and water fill issues with this dishwasher pressure sensor. Monitors water level for proper fill cycles. DIY repair in about 1 hour.
Do-It-Yourself Stories from Customers like You
H2o error code Joe D. • Lockport , NY • August 07, 2025
Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm
Read more
More
$29.95
- Compare At:
-
$35.34
- You Save:
-
$5.39
Genuine Ge part
By: Ge
Part Number: WD21X10261
The Interlock Switch is an OEM replacement part for GE electric and gas dryers. This safety component monitors the door closure, preventing operation if the door is not securely closed and latched. The switch measures 2 inches long and 1/2 inch wide.
Symptoms of a faulty interlock switch include:
- Dryer failing to start or running with the door open
- Timer display not illuminated when start button is pressed
- Inability to open the dryer door during operation
- Dryer suddenly stopping mid-cycle before fully drying clothes
Causes relate to the internal component contacting the door frame over 50,000 open/close cycles potentially exposing wiring to wear. Regular cleaning the external switch area prevents dust or lint buildup skewing performance.
This genuine GE switch is compatible with Hotpoint and RCA dryers as well.
Note: Can be used as a dishwasher door switch on specific models. Check your model number for the most accurate results.
Do-It-Yourself Stories from Customers like You
Melted door switch. Christopher K. • Greeneville , TN • February 03, 2024
The full story:
Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the...
Read more
More
$28.60
- Compare At:
-
$34.03
- You Save:
-
$5.43
Genuine Ge part
By: Ge
Part Number: WD21X10224
Dishwasher won't start or stops mid-cycle? This door interlock switch detects when the door is closed. DIY repair in about 5-10 minutes with a screwdriver.
Do-It-Yourself Stories from Customers like You
Dishwasher stopping mid cycle and beeping Robert D. • Lincoln , NE • January 30, 2015
I got on the site and shared my issue. It was determined my door switches were bad, as well as my actuator. I ordered the parts (which arrived in just 2 days!) and I fixed it myself in just under 10 minutes, for under $30.00. Thanks guys!!!!
Read more
More
$21.71
- Compare At:
-
$25.83
- You Save:
-
$4.12
Genuine Ge part
By: Ge
Part Number: WD21X479
This float switch detects rising water in the refrigerator drain pan or lower cabinet area and signals the appliance control to help prevent overflow and water damage. Use it to replace a failed or intermittent water-level sensor. What it does:
- Senses high water level in the drain pan or collection area and closes the circuit to alert the control.
- Helps identify causes of leaks and pooling under or behind the appliance.
- Commonly used when symptoms include water on the floor, drip pan overflow, or water-related error/alert conditions.
- Matches OEM function for refrigeration units that include a float-based water-detection circuit.
What's included: One float switch. Install notes:
- Disconnect power to the appliance before starting any repairs; shut off the water supply if working near water lines.
- Access may require removing lower kick plate or back panel; handle plastic clips and fasteners carefully.
- Disconnect electrical connector gently and note orientation before installing the replacement; secure wiring and verify float moves freely.
- Restore power and run a short test cycle or simulate water level to ensure proper operation.
Do-It-Yourself Stories from Customers like You
The dish washer was not fill with water Stanley B. • Newberry Springs , CA • December 14, 2014
1. Removed the water inlet/shut off valve, removed and cleaned the screen. while the valve was removed applied electrical power to the valve and it worked just fine.
2. replaced the broken float switch.
Read more
More
$20.38
- Compare At:
-
$78.77
- You Save:
-
$58.39
Genuine Ge part
By: Ge
Part Number: WB24K5022
Oven light switch.
Do-It-Yourself Stories from Customers like You
Rocker switch failed in the "on" position had to get a ge part for a magic chef oven John B. • Seabrook , TX • January 25, 2016
Slid the oven out. Opened the control panel. Shut the power off. Replaced the switch. reversed the steps.
Read more
More
$38.95
- Compare At:
-
$46.35
- You Save:
-
$7.40