Husqvarna Starter

This is a starter solenoid used in a variety of riding lawn mowers and yard tractors. Unlike most push mowers that are started by pulling a rope and firing a magneto, riding mowers have starters and batteries. The solenoid is the link between the battery and starter. When the ignition key is turned, electricity from the starter flows through the solenoid to the mower's ignition, firing the engine. Because it is the part subjected to abrupt electrical charges, over time the solenoid's internal workings may fail and the device must be replaced. A symptom of a bad solenoid is the if the engine fails to turn over. To make sure the problem is not the battery, turn the ignition switch on and use a screwdriver to simultaneously touch both terminals of the solenoid. If the engine turns over, the solenoid must be replaced. The solenoid sits inside the engine housing by the starter motor. Before starting to replace it, disconnect the positive battery cable. Replacing this device is as simple as disconnecting the wires that attach it to the battery and unbolting it from the engine housing. This solenoid is a genuine OEM replacement part that is manufactured to be an exact replacement for the original part. This solenoid is compatible with Poulan, Husqvarna, Craftsman, and Weed Eater equipment.

The starter spring is what is used to create the recoil to start the engine on pull-start chainsaws, blowers, trimmers, and other lawn equipment. When the starter handle is pulled, the rope extends and pulls on the spring, causing it to tighten and then release, which creates the action to fire the motor. It may also be called the recoil spring, rewind spring, or return spring, but they all refer to the starter spring. Over time, this can become worn with use, and in some situations, it can even break completely. If the starter rope will not rewind into the housing, the spring may be twisted and need to be replaced. If so, this genuine OEM starter spring will do the job for compatible machines. This model is manufactured by Husqvarna and compatible with various Poulan and Husqvarna lawn equipment. This spring may serve as a replacement for many machines including blowers, hedge trimmers, grass trimmers, chain saws, and saws. Check the user manual for compatibility and fit, as well as part numbers. Be sure to install this according to all instructions and diagrams for safe and proper operation.

This is a starter assembly with a specific design for Husqvarna handheld backpack leaf blowers. It is the same component that is included in the blower that lets a user pull to start the engine. The starter is composed of several parts including a plastic housing, starter spring, starter pulley, and a pull rope with a grip. As time goes on, the parts of the starter assembly can start to wear out or become broken and will need to be replaced.The only tool needed to replace the starter assembly is a standard screwdriver. The leaf blower will have four screws that offer access to the starter assembly. Remove each of the screws and set them aside. Take out the old starter assembly, and the new component can be installed in its place. Reinstall the screws and ensure they are tightened before using the leaf blower again.This starter assembly is an authentic OEM replacement part that is sourced straight from the manufacturer. It is sold as an individual part. The starter assembly is made for use with leaf blowers manufactured by Husqvarna.

The starter pawl bridge provides the resistance for the starter rope that is required to fire the engine. The bridge connects to the flywheel and is responsible for making it spin when the starter rope is pulled. Over time, the pawl can become worn with use. In the event that other starter components go bad, those can also damage the pawl. If the flywheel does not engage, it may be a faulty pawl. Always use gloves when replacing engine components and be certain to disconnect the spark plug before working on any engine parts. This OEM starter pawl bridge is manufactured to exact standards and is made by Husqvarna. It is compatible with select Husqvarna and Jonsered trimmers. This durable replacement part is made of metal and sold individually.

This replacement starter spring is a genuine OEM model from Husqvarna. The starter spring, also sometimes called the recoil spring or recoil starter spring, is part of the entire starter assembly. It attaches to the fan and flywheel housing and is responsible for helping to retract the starter rope when it is pulled to engage the engine. Over time, the spring can wear out or become twisted. This can cause the starter rope to no longer retract or it can even seize up the entire starter assembly. Replacement of the spring is the only option and this OEM part can provide an exact fit for select engines. This part is designed for use with blowers, edgers, trimmers, and pruners that feature Husqvarna engines and that are manufactured by brands like Weed Eater, Poulan, and Husqvarna themselves. The starter spring is made of durable metal and is sold individually. Always disengage the spark plug and allow the engine to cool completely before beginning and repair projects, and protect the hands by wearing gloves.

This replacement part is a starter pulley. It is a genuine replacement part made by Husqvarna. These types of pulleys are commonly responsible for making sure that two different parts are working together. These two parts usually require a rotating or turning motion. The pulley is situated so that they are able to work together when the appliance is in use to help operate the engine.A new starter pulley might be needed if the turning or rotating motion inside the engine is not working properly. This can be because the pulley is broken or damaged in some way and not able to provide the motion for linkage of the parts. Because this part is situated near the engine, be sure the appliance is cooled off before attempting this repair.This pulley is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer.

This is a starter pulley that is used with various types of string trimmers from major manufacturers.The pulley keeps the starter rope in the right location so that the chainsaw comes on and offers cutting power. Through wear and tear or impact, the starter pulley can break or become damaged.If a user pulls the starter rope and the engine does not start, the starter pulley may not be working correctly. It will need to be replaced. Before the replacement is made, make sure the tool is turned off and the spark plug wire is disconnected. The starter pulley and rope can be reached by disassembling the trimmer. The recoil spring should be rewound before the rope is threaded back in.This starter pulley is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The component is made for use with string trimmers manufactured by Turf King, Craftsman, Paramount, Weed Eater, Poulan, and Poulan Pro.

This rewind spring is a genuine Husqvarna part, sold individually. This rewind spring can be used as a replacement part in a string trimmer or an edger. The rewind spring maintains the placement of the pulley in the pull start assembly, allowing the rope to power the appliance.The rewind spring could be dented, punctured, warped, eroded, cracked, chipped, or otherwise damaged to the point of reduced functionality or negated functionality, in which case the rewind spring should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This rewind spring is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, and Poulan.

This starter spring is a genuine OEM replacement part for chainsaws that operate using a starter rope. When an operator pulls the starter rope out, there is a pulley around which the rope then has to recoil. The starter spring maintains tension in the pulley so that the rope will naturally recoil. The starter spring also provides enough tension to prevent the operator from yanking the rope all the way out of the assembly. Through repeated use, and especially if an operator is rough on their appliance, the starter spring can loosen up and will no longer work as effectively. When this happens, the starter pulley will not recoil and the starter rope will hang loose from the appliance. Fortunately, switching out the starter spring is an easy repair that should only require a wrench and a pair of pliers. Be careful when pulling the old spring out. Although it isn't as tense as it once was, it still has the potential to snap back. This replacement starter spring is a high-quality part for Husqvarna, Poulan, and Weed Eater appliances, and as such, it is sourced from its original manufacturer. This part does not ship with any additional hardware.

A new rope kit may be necessary if the original rope becomes deteriorated or frays with regular equipment use.This rope is part of the recoil starter assembly, an essential component that enables the motor to be pull-started. Due to frequent usage and wear and tear, the rope can easily fray. Without this rope the engine cannot be manually pull-started. It is manufactured from durable nylon.This Husqvarna rope kit is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement Husqvarna rope kit fits various different models of Husqvarna, Poulan, and Craftsman blowers, trimmers, and hedge trimmers. Please note this is sold individually. Handle grip not included.

This is an OEM replacement starter pulley kit designed for use with gas chainsaws. The starter pulley assembly replaces the components of your recoil starter that may fail due to normal wear and tear. The pulley and return spring react to the pull of the starter rope and then engage the flywheel. This is what fires the chainsaw engine. If the starter rope is not reacting or the flywheel is not engaging, there may be an issue with the starter pulley assembly. This repair can be completed with a screwdriver and pliers and doesn’t take a lot of time. This starter pulley kit is a genuine product from Husqvarna, and it is designed for use with Poulan, Jonsered, and Husqvarna engines and outdoor power equipment. This kit includes the plastic pulley, return spring, hub, and two screws for securing the unit. The housing, rope, and starter grip will be sold separately if replacements are needed.