Husqvarna Carburetor

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

This high quality choke lever is used on string trimmers and edgers from multiple manufacturers. The plastic choke lever actuates the choke valve which creates a limit to the amount of air that can enter the engine when the equipment is cold started. If the choke lever has been damaged or is broken, it may create problems with starting the tool. If this is the case, the choke lever will need to be replaced.This is a simple replacement project that requires only a screwdriver and a pair of work gloves. Before starting, make sure the tool is turned off and the spark plug wire has been removed. Place the tool on a flat surface and take out the choke lever. The broken choke lever can be removed using the screwdriver. The new replacement choke lever can be installed before tightening the screws and using the equipment again.This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The choke lever is made for use with edgers and string trimmers manufactured by Craftsman, Husqvarna, and Poulan.

This certified OEM replacement part is a carburetor kit for a gas-powered leaf blower engine. For gas to ignite in an engine, there has to be the right amount of air in the system. Without oxygen, the spark won't light and the gasoline will not ignite. A carburetor is responsible for maintaining the right balance of air and gasoline. Therefore, without a properly functioning carburetor, the engine will also not function properly. Carburetors begin to break down over time because of built up exhaust and gunk in the engine. As this grime builds up, the carburetor cannot get enough air and the balance is thrown off. While carburetors can sometimes be cleaned, if it has become overly clogged or damaged, it will need to be replaced. Signs of a faulty carburetor include shakiness and black smoke, backfiring, hard starts, or an engine that will not start at all. Replacing a leaf blower's carburetor requires the crankcase line, primer line, fuel line, air filter, and throttle linkage to all be disconnected using pliers and a screwdriver. This part is intended for Craftsman, Poulan, Weed Eater, and Husqvarna leaf blowers and is sourced from the original manufacturer. It ships individually.

This carburetor is designed to mix gas and oil together before moving the mixture into a chainsaw's engine. It is a single-cylinder model with an auto-choke system and requires regular maintenance to stay in good shape. Changing the oil, replacing the air filter, and adding a fuel stabilizer will help keep the engine performing at its best. If the carburetor isn't working properly, this may be due to blockages of debris, dirt, and fuel. If the fuel tank is full but the engine refuses to start, it's a good idea to test the carburetor for problems. Take out the air filter and then pour a small amount of fuel into the carburetor itself. Yank on the starter rope and see if the motor starts. It should die shortly after. If this occurs, the carburetor may have a problem and require replacement. This is an individual part that is compatible with Poulan, Craftsman, and Husqvarna chainsaws. The carburetor is a genuine OEM product that is provided directly from the manufacturer. It comes with a rubber O-ring and a gasket. A screwdriver will also be required to make a replacement.

The carburetor is responsible for mixing the air and fuel before it enters the engine. It consists of intake and outflow valves, as well as a float and needle to monitor and manage the flow of fuel and air coming into and leaving the carburetor body. The fuel mixes with oil in the smallest part of the body and is then pushed through a butterfly valve into the engine. Adjusting the valve will adjust how much of the fuel mixture gets into the engine. In the event that an engine is not running or keeps stalling, the carburetor may need of repair or replacement. This kit is designed to assist with the repair or refurbishment of several carburetors in various chainsaws. It is a full carburetor, not a rebuild kit. Installation will require a screwdriver to replace the carburetor. This OEM carburetor assembly kit is compatible with a number of chainsaws from Husqvarna. The kite includes the carburetor body, along with the float, needle, gaskets, and seals that are all made to manufacturer standards, offering an exact fit for compatible models.