Parts for Electrolux ERMC2295AS: Ice Makers & Container Parts

This is a replacement screw used to secure appliance panels and components. It restores proper fastening to stop rattles and keep parts aligned for reliable operation. What it does:

• Secures trim, brackets, or small panels to the appliance
• Prevents loose parts that can cause vibration, noise, or improper sealing
• Restores factory fastening where a screw is missing or damaged
• Simple, single-purpose fastener — use where the original screw was installed

• Use the matching screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage
• Disconnect power or follow appliance safety steps when working near electrical components
• Replace only the screw(s) that match the original size and type

This replacement mounting bracket secures internal appliance components to the cabinet or frame, restoring stable alignment and reducing unwanted movement. Use it to replace a bent, broken, or missing bracket that causes loose parts or noise. What it does:

• Provides a secure attachment point for internal panels, rails, or assemblies
• Restores proper alignment to reduce rattling, vibration, or shifting parts
• Replaces damaged or corroded brackets that no longer hold components firmly
• Helps prevent further wear on connected parts by keeping them correctly positioned

• One replacement mounting bracket as shown

• Installation requires basic hand tools; disconnect power and water before beginning
• Retain all fasteners and observe any orientation noted during disassembly for correct reinstallation
• If the original bracket is fastened to electrical components or wiring, handle with care and avoid pinching wires

The Ice Maker Assembly is an OEM part for Frigidaire refrigerators. It is responsible for automatically producing batches of ice through a process of freezing water into cube form. The ice maker works in conjunction with the refrigerator's freezer compartment and water supply line to perform its ice production function. 

Symptoms of a faulty ice maker include:

• Failure to produce ice cubes
• Oddly shaped, sparse, or chunky ice output
• Leaks or water pools in the freezer 
• Strange noises coming from the ice maker area
• Error codes shown regarding ice maker performance

Causes of a bad ice maker assembly can include issues with components like the mold heater, water valve, or agitator that are vital to the freezing process. Improper refrigeration temperatures or clogs preventing water flow can also negatively impact ice production.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This single water inlet valve regulates water flow into your refrigerator. When energized, it opens to supply water and closes to stop it—restoring consistent filling for ice production and any water dispensing your model supports.

• Controls on/off water flow to the ice maker and/or dispenser (model dependent)
• May resolve no ice, slow or hollow cubes, or a dispenser that won't dispense or is weak
• Can correct intermittent dripping or leaks at the rear caused by a valve that won't fully close
• A humming valve with little or no water flow can indicate a failed solenoid or internal blockage

• Unplug the refrigerator and shut off the household water supply before servicing
• Place a towel/container to catch residual water; relieve line pressure if possible
• Note wire and tube locations; transfer to the new valve and seat/tighten fittings securely
• Restore water and power, then check all connections for leaks and run a test fill

This replacement tube restores proper fluid routing inside compatible Frigidaire appliances, helping stop leaks and return correct flow to affected components. Use when original tubing is cracked, clogged, or damaged. What it does:

• Routes fluid between internal components so systems like dispensers or ice makers can receive water or allow drainage
• Replaces cracked, split, or deteriorated tubing that causes visible leaks or pooling
• Helps resolve intermittent or weak water flow when the tubing is blocked or pinched
• Restores sealed connections when clamps or fittings no longer hold the original tube

• Disconnect power and shut off the water supply before starting any repair
• Inspect fittings and clamps; replace clamps if they are corroded or damaged
• Trim tubing squarely and seat fully on barbed fittings; secure with the correct clamp type
• After installation, restore power/water and check all connections for leaks

Color: Black/natural. Nylon

This is a replacement mounting screw used to secure appliance panels and small components so parts stay firmly in place during normal use. Installing the correct screw restores proper fit and reduces rattles or loose trim. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces a lost or stripped screw to restore secure attachment
• Helps maintain safe, stable operation by holding parts where they belong

• One replacement mounting screw

• Disconnect power and water before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can damage threads or panels
• Keep removed fasteners organized so you reinstall them in the original locations