Parts for Electrolux E23CS75DSSA: 15 - Ice & Water Dispenser Parts

Water supply tube that routes water through your refrigerator to the ice maker and dispenser. Replace if cracked, leaking, or damaged during moving.

Torsion spring that returns the dispenser ice chute door to closed position. Replace if broken, weak, or missing to restore proper door closure.

Single mounting screw for securing refrigerator panels, brackets, and trim pieces. Replaces worn, stripped, or missing screws to restore proper fit.

Replacement defrost drain pan installs under the freezer compartment to collect and direct condensate water. Replace if cracked, broken, or missing.

Motorized actuator that opens and closes the refrigerator ice dispenser door. Replace if door won't open, closes slowly, or plastic gears are cracked.

Replaces the paddle lever you press to dispense ice or water. Install when the original actuator is cracked, broken, or worn for smooth operation.

Insulating foam that installs on the ice chute door to prevent warm air and moisture around the dispenser. Replace if compressed, cracked, or missing.

Rubber ice dispenser door center seals the ice chute on your refrigerator. Replace if cracked, worn, missing, or not sealing properly to stop frost buildup.

Rubber seal for the ice dispenser door on side-by-side refrigerators. Replaces cracked, worn, or missing seals that allow warm air into the freezer.

Bracket that supports and aligns the ice dispenser door. Replace if broken, cracked, or causing the ice door to hang open or fail to seal properly.

Dispenser not responding or lights out? This control board restores ice and water dispenser function. Moderate DIY repair, requires removing door panel.

The Ribbon Cable Harness is an OEM part for Frigidaire refrigerators. It connects various electronic components within the refrigerator, facilitating communication and control signals between them. This harness is essential for the proper functioning of the refrigerator's electronic systems.

Causes of a bad cable harness can include physical damage from bending or pinching, wear and tear from regular use, or electrical failures that disrupt signal transmission. Ensuring the integrity of this component is crucial for maintaining the appliance's performance.

Symptoms of a bad ribbon cable harness include:

• Intermittent or complete loss of electronic functions
• Error codes or malfunctioning display
• Unresponsive buttons or controls
• Inconsistent operation of refrigerator features

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Fix a dispenser that won't stop running water or ice, or won't dispense at all. This switch controls water and ice flow. Moderate DIY repair.

Pivot pin for refrigerator ice dispenser door hinge assembly. Replace if worn, broken, or missing to restore proper door alignment and movement.

Secures the micro switch in your refrigerator's ice dispenser assembly. Replace if screw is rusted, stripped, or missing to properly mount the switch.

Screw secures handles and components on freezers and refrigerators. Replace if stripped, broken, or missing. 10-16 x 0.500 threading fits most models.

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Bearing plate for side-by-side refrigerators. Mounts and supports rotating components. Replace if cracked, worn, or broken to restore stability.

This water inlet tube supplies water from the refrigerator's supply to the dispenser and ice maker, restoring proper flow and preventing routing issues. It's a direct-fit replacement that helps stop leaks and restore water delivery. What it does:

• Directs water from the house supply to the refrigerator's internal water system.
• Restores water flow to the dispenser and ice maker when a damaged tube is blocking supply.
• Prevents leaks and water pooling caused by cracked, pinched, or corroded inlet tubing.
• Works with other inlet fittings and valves to maintain proper water routing.

• Shut off the refrigerator power and water supply before starting any work.
• Remove access panels as needed and relieve any residual water pressure in the line.
• Use proper tubing connectors and tighten fittings to manufacturer torque—inspect for leaks after restoring water.
• If you find additional damaged fittings or clamps, replace them to ensure a leak-free install.

Fix frozen water dispenser issues with this dispenser heater kit. Prevents ice buildup in the fill tube and restores water flow to your refrigerator.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.