Ikea Dishwasher Parts

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

12 Ft in length

This main electronic control board governs the appliance's user interface and cycle functions, restoring responsive controls and correct operation when the original board fails. Replace a faulty control board to correct erratic or unresponsive behavior. What it does:

• Receives input from the console and sends control signals to relays, valves, motors and sensors.
• Restores normal cycle selection and timing when a failed board prevents the appliance from starting or completing cycles.
• Addresses symptoms like unresponsive or non-working buttons, blank or erratic displays, and unexpected program changes.
• Interfaces with safety and feedback sensors to coordinate appliance functions.

• Always disconnect power to the appliance before replacing the control board to avoid shock or damage.
• Handle the board by its edges and avoid touching circuit traces or components; the board is static-sensitive.
• Note connector locations or photograph wiring before removal to ensure correct reassembly.

Located between the console and door

This dishwasher circulation pump and motor assembly moves wash water through the spray arms during the cycles. Replacing a failed or noisy unit restores proper water flow, spray pressure, and reliable cleaning performance.

• Circulates water from the sump through the spray arms during wash and rinse
• Provides the pressure and flow needed for effective cleaning
• Common failure symptoms: little or no spray action, poor cleaning results, loud humming/rumbling/grinding during wash
• Water leaking from the pump area can also indicate a problem with this assembly

• Disconnect power at the breaker and shut off the water supply before servicing
• Access from the bottom/front; remove the toe panel and pull the dishwasher out if needed for clearance
• Expect residual water; place towels or a tray to catch spill, and note wire/connector orientation before removal
• Ensure all connections and seals are properly seated; run a short fill/rinse to check for leaks before reassembly

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.

The Control Board is an OEM replacement part for Frigidaire dishwashers. Located inside the cabinet behind the control panel, the control board utilizes integrated circuits and electronic components to regulate all dishwasher functions. It receives input signals from the control buttons to initiate and monitor the wash cycle. 

Causes of a bad control board can include failures of electronic components over time, voltage fluctuations that cause circuit damage, or moisture infiltration leading to corrosion.

Symptoms of a bad Control Board include:

• Dishwasher fails to start or stops mid-cycle unexpectedly
• Lights or displays on control panel malfunction  
• Inability to select options or cycles
• Complete non-responsiveness of control functions

This board is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

Used on the upper dishwasher dishrack.

The Rack Wheel is an OEM part for Whirlpool dishwashers. As an internal component that guides dish rack movement, the rack wheel works along the rack rail system to smoothly raise and lower racks in and out of the wash chamber. 

Causes of a bad rack wheel can include normal wear stripping lubrication from prolonged usage, or accidental impacts warping its circular shape.  

Symptoms of a bad rack wheel include: 

• Difficulty pulling out or pushing in dish racks  
• A rack that gets stuck and does not fully recline or rise
• Rack trays that cannot pivot to different levels during a cycle
• Reduced wash effectiveness from poor rack positioning

This OEM Whirlpool part is also compatible with some Maytag, KitchenAid, and GE dishwashers.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

Color: Black. Instruction sheet included.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This fine mesh plastic screen filters debris from the water path to protect downstream components and help maintain proper wash performance.

• Traps fine particles to prevent clogs in the circulation/inlet path
• Helps reduce spray pressure loss and poor cleaning results
• Can address issues like gritty residue, reduced water flow, or noisy pump operation
• Wear, mineral buildup, or tearing can require replacement

• Disconnect power and shut off water before service
• Note orientation and seating of the original screen; install the replacement fully and evenly
• Inspect surrounding seals and mating parts; clean any sediment before reassembly
• Restore power/water and check for leaks and proper operation