Ikea Refrigerator Grille

The Kickplate Grille is an OEM part for Whirlpool refrigerators. It is installed at the base of the refrigerator and serves to cover and protect the lower ventilation area, helping to ensure proper airflow to the condenser and other components. It measures approximately 37 inches wide, 2 inches high, and 4 inches deep. 

You should replace the kickplate grille if it becomes damaged or broken. Causes of a bad kickplate grille can include accidental impacts, wear and tear over time, or exposure to cleaning chemicals that can weaken the material.

Symptoms of a bad kickplate grille include:

• Visible cracks or breaks in the grille
• Loose or unstable attachment
• Obstructions in airflow leading to poor refrigerator performance
• Accumulation of dust and debris behind the grille

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: Grey

This front toe-kick grille mounts across the bottom of the refrigerator. It restores a clean, finished look while helping direct airflow through the condenser area and shielding components from bumps, dust, and debris.

• Provides the finished kickplate across the lower front of the cabinet
• Helps direct ventilation airflow through the condenser compartment
• Replace if cracked, warped, missing, or if it won't stay attached
• Can eliminate rattling from a loose or damaged kickplate

• Disconnect power before servicing
• Remove the old grille by releasing snap tabs or removing screws (varies by model)
• Align the new grille with the mounting slots and press firmly until it seats, or reinstall screws
• Ensure vent openings are clear and that doors open/close without interference

This base grille covers the lower front of the refrigerator in a midnight gray finish. It directs airflow to the condenser and protects internal components—restoring proper ventilation and a clean, finished look when the original is damaged or missing.

• Covers the toe-kick area and helps channel cooling air through the condenser compartment
• Protects coils and lower components from bumps and debris
• Restores the unit's finished appearance
• Common symptoms include a cracked or missing grille, loose/rattling panel, or broken mounting tabs

• Disconnect power before servicing; use gloves to protect hands from sharp edges
• Open the doors; remove any retaining screws or release the grille's clips, then pull the old grille forward
• Align the new grille with the mounting points and snap or screw into place
• Ensure vents are unobstructed and the grille is secure before restoring power

This toe grille is the lower front kick panel that covers the refrigerator's base and leveling feet. It restores a clean, finished look and helps direct airflow to the condenser area for proper cooling performance.

• Covers the bottom front opening and protects components from bumps and debris
• Helps channel air across the condenser area
• Common signs it's needed: cracked or broken panel, missing grille, difficulty keeping grille attached
• Cosmetic damage or loose fit at the base of the refrigerator

• Unplug the appliance before servicing
• Open the doors to relieve pressure on the grille, then release retaining tabs or screws
• Align tabs and snap or screw the new grille into place
• Verify doors open/close freely and grille is secure

The Grille is an OEM replacement part for Whirlpool refrigerators. It covers the gap between the bottom of the refrigerator and the floor, providing a clean and finished look to your kitchen. It helps protect the internal parts from dust and debris while also preventing small items from rolling underneath the appliance.

Symptoms of a bad toe grille include:

• Visible cracks or damage
• Discoloration or fading
• Missing pieces or gaps in the grille

A damaged or worn-out toe grille can occur due to regular use, accidental impacts, or general wear and tear over time. If you notice cracks, discoloration, or missing pieces on the toe grille, it may be time to replace it.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This 30-inch toe grille restores the finished look at the bottom front of a range or oven while protecting the lower cabinet area from debris. It's a direct-fit exterior trim piece that keeps the appliance appearance clean. What it does:

• Covers and protects the appliance lower front, hiding components and braces.
• Restores a damaged, missing, or dented kickplate to improve the appliance's appearance.
• Helps prevent debris buildup under the appliance and reduces visible gaps.
• Stops rattling or loose trim caused by broken or warped grille pieces.

• High-level replacement: typically installs from the front and secures with clips or screws.
• Disconnect power and move the appliance per the manufacturer instructions before doing any service that requires pulling the unit forward.
• Wear gloves to protect hands and avoid scratching the grille finish during installation.
• Retain or reuse original fasteners when possible; obtain OEM replacement hardware if fasteners are missing.