Ikea Refrigerator Parts

• Touchpad does not respond
• Ice maker not making ice

Located the Whirlpool crisper pan on AppliancePartsPros.com on Monday morning and received the crisper pan on Tuesday afternoon. Doesn't get any better than than!! I will be repeat business in the future!! Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

All you need is a nut driver. The end cap is attached to the side of the refrigerator cabinet with two long screws. Once you remove them, you should slide the end cap towards you. It will release the internal clip that holds the front of the end cap. You should then unscrew the metal slider from the end cap. Assembly of the new end cap is the reverse. You should first attach the metal slider to the new end cap. Attaching the new end cap to side of the refrigerator cabinet is a little tricky.... Read more

While looking for parts thru AppliancePartsPros.com, I found a diagram with my refrig model # for the door shelf bin. It was a perfect match. Prior to that I've spent countless hours searching and became very frustrated. The diagrams and videos were very helpful. Thank you, KShigeta Read more

I replaced the icemaker. It was fairly easy, with the most difficult part being access to the icemaker in the bottom freezer. I loosened two screws, removed one additional screw, disconnected the wiring and removed the old icemaker. I mounted the wiring harness and ice level sensor arm from the old unit onto the new icemaker and installed it with no problems. I wish I'd done this months ago instead of repeatedly attempting to repair the old icemaker. Read more

• Not dispensing water

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

Installed replacement drawer Read more

• Ice maker dispenses too little ice
• Ice maker dispenses too much ice
• Ice maker won't dispense ice
• Ice maker not making ice

Replace assembly Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

It was a classic horror story, but with a happy ending! I called a classic, "regular" repair company that I obtained on-line. My Whirlpool was 2 months out of warranty, so the repairman charged a trip-fee of $95 that would be subtracted from the cost of my repair. "Lee" showed up an hour late, even though he was told that I had to leave for work by 10:30 (-He assured me that he would have me fixed by then). The refrigerator was rolled out of its spot, and Lee began to remove the back cover... Read more

• Fridge runs too long
• Freezer not defrosting
• Freezer too cold
• Won't start

A bit of research on the internet indicated the most likely problem was with the defrost system. I found the service manual for the refrigerator and was able to determine that the defrost heater and thermostat passed the self test. The refrigerator would perform a forced defrost which resulted in a cold refrigerator. More research revealed that this particular refrigerator does not have a defrost timer, instead the defrost cycle is controlled via the Electronic Control board which is also... Read more

• Frost buildup
• Freezer not defrosting
• Freezer section too warm
• Fridge too warm

Condenser was encased in solid block of ice due to automatic defrost not working. Replaced thermostat and ADC control board. Working fine now. Most tedious part was using a heat gun to melt all the ice off the condenser coils. You will need a couple small wire nuts to splice the new thermostat into the existing harness (they are not included). Service tech wanted over $400 to repair, fixed it myself for half that. Thanks ! Read more

• Frost buildup
• Leaking

The drain tube for for the defrost cycle seemed to be blocked, so I googled the repair & it sent me to AppliancePartsPros. Obviously, there's a design problem with this model since many other people have the same issue. This tube is an upgrade on the original for my KitchenAid model (design flaw). Since installation 4 days ago, I have had no leaks - awesome! The video for installation of the new tube on AppliancePartsPros was excellent. Two additions to the video: 1) I used a hair dryer... Read more

Living in Texas it is hot all the time, even in fall, so our family loves our cold filtered water and ice. We woke up one morning with water all over the floor in the kitchen. It looked like it was coming from our freezer through the ice dispenser. We turned off the water shut off valve and removed what was now a giant block of ice instead of an ice dispenser from our freezer to melt in the sink. Since we have used AppliancePartsPros.com before, I knew exactly what I needed to do to see if we... Read more

Removed freezer door by removing 4 bolts holding slide tracks for freezer basket. Pulled out old gasket. Soaked new gasket in hot water to smooth out a crease that resulted from shipping. Installed new gasket, starting at corners. Used a blunt tool to push new gasket into slot at the corners. Set remaining gasket material with hands. Used putty knife to tuck edge of gasket under lip along door. Reinstalled door. Take care to line up door perpendicularly. There is some play when... Read more