Inglis Dryer Parts

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Use the videos on this website here and you can repair most brands. Many are duplicate in design. 1. Unplug the machine. 2. Move it away from a confined area to get more room. 3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet. 4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you... Read more

Replace the drum drive belt and tension pulley assy. Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

Installed new drive motor. We are an animal emergency hospital and need clean laundry 24/7. I received motor the next day and was fixed by 3 PM. Most of the time spent repairing is actually spent on cleaning out all the lint inside of machine. Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

Went on YouTube and found out how to replace switch. Had it replaced in no time. Read more

Tested upper thermostat for continuity and had none. Cleaned exhaust of excess lent. Changed cycling thermostat and cutoff terminal. And now she works great. Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

Replaced start switch. Read more

Replaced the timer - This should have been a VERY easy repair however, there is a clip (holding the timer to panel) on the bottom of timer than must be removed with a pair of pliers. There is absolutely NO room to access this clip so I had to take apart much of the dryer to gain access. What should have been a 15 minute repair turned into a frustrating hour. Read more

Replaced timer. It's a snap in place timer, once you remove the defective timer, overall pretty easy. Read more