Jenn-Air Dishwasher Control Board

This genuine replacement part is a control board for Whirlpool dishwashers. The control board is the main circuit board that controls the dishwasher's main functions. If the dishwasher is no longer turning on, or is not draining properly, it might be time for a new control board. Luckily, replacing a control board is an easy process.First, remove the outer door panel of the dishwasher by unthreading the mounting screws. Lift the control panel up and disconnect the wire touchpad harness from the control board. Then use a flathead screwdriver to release the locking tab and slide the control board housing to the left to detach. Remove the wire covers. Once removed, take note of the orientation of the wire connectors and disconnect them from the old board. Install the new control board by reconnecting the wire connectors to the appropriate terminals. Align the wire covers and pop them into place. Insert the control board housing tabs into the slots of the mounting bracket and slide the housing to the right to secure. Reinstall the control panel by attaching the control pad wire harness to the new board. Align the panel and rethread the mounting screws to secure. This replacement control board is compatible with Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand dishwashers.

This electronic control board is the central "brain" of your appliance. It manages power distribution, sensor inputs, and timing so selected functions run correctly. Replacing a failed board restores proper operation and reliable, responsive controls.

• Coordinates and sequences operations based on user selections and built-in programming
• Interprets inputs from sensors/switches and communicates with the user interface
• Drives components such as motors, pumps, valves, and relays as required
• Common symptoms of a failed board: appliance won't start or respond, cycle won't advance, stops mid-operation, intermittent behavior, or error/blinking status codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the PCB by the edges to avoid static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require service-mode setup or programming after installation—follow the tech sheet for your unit

This electronic control board is the dishwasher's brain, managing cycles and powering the pump, valve, heater, and other loads. Replacing a failed board restores normal start, wash, drain, and dry functions.

• Coordinates and times wash cycles based on user selections and sensor inputs
• Sends power to the circulation pump, drain pump, water inlet valve, and heater
• Interfaces with the user interface and monitors door/latch status
• Failure may cause: no start, cycle won't advance or ends early, no fill/drain/heat, or error codes

• Disconnect power at the breaker before servicing; verify power is off
• Access location varies by model; commonly behind the lower toe panel or inside the console
• Handle the board by the edges and observe ESD (anti-static) precautions
• Move wire connectors one at a time from the old board to the new, secure the board, and reassemble; run any required diagnostics/reset per your model's tech sheet

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions

The Control Board is an OEM part for Whirlpool dishwashers. It serves as the central control unit, regulating various functions such as cycle selection, water temperature, and drying operations through its electronic components.

Causes of a bad control board can include power surges, electrical shorts, water damage, or simply wear and tear over time.

Symptoms of a bad Control Board include:

• The dishwasher not starting or responding to inputs
• Error codes or indicator lights illuminating
• Cycles not running or completing properly 
• Issues with water intake, draining, or heating
• Strange noises or abnormal behavior during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.