Jenn-Air Control Board

• Fridge runs too long
• Freezer not defrosting
• Freezer too cold
• Won't start

A bit of research on the internet indicated the most likely problem was with the defrost system. I found the service manual for the refrigerator and was able to determine that the defrost heater and thermostat passed the self test. The refrigerator would perform a forced defrost which resulted in a cold refrigerator. More research revealed that this particular refrigerator does not have a defrost timer, instead the defrost cycle is controlled via the Electronic Control board which is also... Read more

• Too warm
• Fridge runs too long
• Fridge too cold
• Frost buildup

A word of thanks to AppliancePartsPros - they delivered in one day. Ordered at 4PM CDT and received the part by noon the next day. Also, Alicia in the help department was able to locate an electrical diagram for my old freezer. This was essential for proper setup and her persistence in tracking down the diagram was top notch. Now on to my problem. One day I opened the freezer and found frost and thawing food. I attributed this to the door hitting an item in the freezer and not completely... Read more

Test showed it was the infrared sensor, so I ordered the replacement parts, which arrived with standard shipping in just a couple of day. The video on the site show exactly what to do. The fix and installation of the replacement part was quick and easy. My ice maker is producing ice like bran knew. I could not be happier with the service and information provided by this site. Great job guys, really great job. Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

Ordered two boards which were indicated as the possible problem. I took detailed pictures of each board before removing to assure I was reconnecting all the connections correctly. I used a long set of needle nose pliers to remove each connector. The tricky part was trying to figure out how to remove the boards. So far when I experience a power loss the frigid has successfully restarted. Fingers crossed!! Read more

• Won't start

Replaced the Inverter box Read more

• Won't start

I purchased a new igniter for the bake assembly and found that it, unfortunately, did not resolve my problem. I measured the resistance of the different points on the gas valve and it was reading within spec so I then purchased this spark module and it did the trick. My gas range is a Kitchenaid kgsk901sss02. I had a LOT of trouble finding where the spark module is located, and eventually found a schematic that shows it's location behind the front control panel of the oven. Upon taking the... Read more

• Timer will not advance

I followed troubleshooting guide and repair videos offered on website, ordered replacement oven control board and reinstalled unit using only a 1/4 inch nut driver. Easy fix for do it yourselfer in 15-20 minutes. Make certain to have model number of appliance when ordering. Parts are somewhat pricey but AppliancePartsPros. were much more reasonable than local parts supply houses or other sources plus they offered 1 year replacement even on electrical stuff. Read more

Bought new optic control boards, both the emitter and the receiver. The repair process was so simple. The KitchenAid repair tech came out to diagnose our issue. He was only going to come back and install a new emitter. They wanted a lot of money to do the repair. They were going to charge us $257 just for the part (emitter board). We bought both boards for $300 from AppliancePartsPros. We decided to replace both boards, because if one went bad the other might not be far behind. Read more

Replaced numerous items including this Inverter and two control boards but the Magnetron was the ultimate solution. The tip was clearly burned through when I removed the original. Read more

Ordered the electronic control board turns out that was not my problem called Appliance Parts for technical assistance and they suggested I order the Panel Control. Fixed my JennAir within thirty minutes. Packed up first parts a instructed by my return authorization, received credit for returned part. Wonderful experience with all at Appliance Parts. Read more

Ordered the controller and installed it. Now it works like a charm. Read more