Jenn-Air Range / Cooktop / Oven Parts

This top burner valve switch mounts to a surface burner gas valve and closes the ignition circuit when you turn the knob to Lite. Replacing a worn switch restores dependable sparking and stops intermittent or nonstop clicking at the burners.

• Mounts on the surface burner valve and closes the ignition circuit at the Lite position
• Signals the spark module to fire the igniters so the burner lights
• Helps ensure quick, consistent burner ignition
• Common symptoms: no spark at a burner, intermittent ignition, or continuous clicking with knobs in Off

• Disconnect power and shut off the gas supply before servicing
• Pull off the burner knob and remove the control/manifold panel to access the valve switch
• Transfer wires one at a time and align the switch correctly on the valve stem; avoid overtightening
• Reassemble, restore power, test for spark with gas off, then relight and check for leaks

Replace a damaged or missing selector knob to restore smooth, precise control of your appliance settings. This knob fits onto the selector switch shaft so you can easily turn and choose functions as intended.

• Attaches to the selector switch shaft to turn and select functions/settings
• Replaces a cracked, stripped, wobbly, or missing knob
• Helps when the knob slips or won't stay on the shaft
• Restores proper alignment with panel markings for accurate selections

• Disconnect power and allow the appliance to cool before servicing
• Pull the old knob straight off; if tight, gently wiggle while pulling
• Align the new knob with the keyed/flat on the switch shaft and press fully into place
• Verify smooth operation and correct pointer alignment with panel markings

This LP conversion kit adapts compatible gas appliances from natural gas to liquid propane. Proper conversion helps ensure safe ignition, correct flame size, and consistent heating when your installation uses propane instead of natural gas. What it does:

• Converts the appliance's gas system from natural gas to LP/propane
• Matches burner/orifice sizing and regulator setting to propane fuel characteristics
• Helps correct symptoms tied to the wrong fuel: tall yellow flames, sooting, weak heat, uneven burner performance
• Required when connecting the appliance to an LP/propane supply

• Includes LP conversion kit

• Must be installed by a gas technician; follow local codes and the model-specific instructions
• Shut off gas and power before starting; verify all connections are leak-free with an approved leak-detection solution
• Replace the specified orifices and set/convert the pressure regulator to LP as directed; apply the provided LP identification label
• After conversion, verify flame appearance and manifold pressure

Color: White

This radiant surface element restores proper heat to a glass-ceramic cooktop burner. When the original element burns out or develops hot spots, replacing it brings back steady, controllable heat for everyday cooking. What it does:

• Generates heat for the selected cooking zone beneath the glass top
• Works with the surface control to cycle on/off and regulate temperature
• Helps deliver even heating across cookware
• Common fix for: burner won't heat, heats slowly or unevenly, only part of the burner heats, visible damage on the element

• 1 radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Support and handle the glass top carefully to avoid damage
• Note wire locations and transfer any mounting hardware from the old element
• After reassembly, test the burner on low and high settings

This surface radiant element sits beneath the glass cooktop and generates heat for one cooking zone. Replacing a failed element restores proper heating performance and dependable temperature response on the affected burner.

• Supplies electric heat to the selected surface burner under the glass top
• Common symptoms: burner won't heat, heats weakly or inconsistently, or only part of the ring glows
• Visual damage (burn spots/breaks) or an open reading on a continuity test indicate replacement
• Similar symptoms can also result from a faulty surface switch or wiring—diagnose before replacing

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift/remove the glass top per your service manual to access the element
• Note wire positions and bracket orientation; move wires one at a time to matching terminals
• Support the glass and avoid stressing the element; test operation before final reassembly

This oven door gasket restores a tight seal between the door and oven cavity so your appliance can hold set temperatures. Replacing a worn seal helps reduce heat loss for more consistent preheating and baking results.

• Seals the gap between the oven door and frame to keep heat and moisture inside
• Helps maintain accurate oven temperatures and reduce energy loss
• Replace if the gasket is torn, hardened, flattened, frayed, or falling out of its channel
• Common symptoms: heat escaping around the door, long preheat, uneven baking, odors or smoke leaking from the oven

• Disconnect power and allow the oven to cool completely before servicing
• Gently pull the old gasket from the channel or unhook its retainers; note clip locations/orientation
• Press the new gasket evenly into the groove without stretching; align any corner pins/clips to match the original
• Close the door and check for uniform contact around the seal

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

Color: metallic. Measures about 10 inches wide by 5 inches deep. Be sure to measure old filter before ordering. If your filter measures approx 11 1/4" x 6 1/8" use R0710163.

Replace a damaged or worn console with this control panel assembly. It restores a clean, secure mounting surface for the user controls and helps protect internal components so your appliance looks right and operates as intended.

• Houses and supports the user interface components (buttons/knobs/keypad and display bezel)
• Keeps controls aligned and securely mounted for proper operation
• Shields internal wiring and control electronics from incidental contact
• Helps resolve issues like loose controls, cracked or warped console fascia, and heavy cosmetic wear

• Disconnect power at the breaker or unplug the appliance before starting; shut off gas supply if applicable
• Remove any knobs/trim and the screws securing the old panel; support the panel while detaching
• Transfer required hardware, bezels, and brackets from the original panel to the new one
• Reassemble carefully and verify controls move freely before restoring power

Color: black. It measures about 2 inches in diameter.

This burner cap sits on top of the surface burner head to shape the flame and shield the head from spills. Replacing a damaged or missing cap helps restore even heating, reliable ignition, and the cooktop's original appearance.

• Covers the burner head and disperses flame for more even cooking
• Protects burner head and ports from food and liquid spills
• Helps maintain proper ignition and a steady blue flame
• Helps with symptoms like uneven/yellow flame, delayed ignition, or poor simmer

• Allow the cooktop to cool completely before handling
• Disconnect power and shut off gas
• Clean the burner head and clear ports before seating the cap
• Center the cap so it sits level and flush; misalignment can affect ignition and flame

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

16K. Mueller.

This griddle creates a flat, continuous cooking surface that rests on your range or cooktop grates. It adds versatile space for items like pancakes and sandwiches, and replaces a worn or missing original griddle to restore safe use. What it does:

• Provides a broad, flat surface across burners for griddle-style cooking
• Direct replacement for a damaged, warped, or missing griddle
• Useful for foods that need a continuous surface (pancakes, eggs, grilled sandwiches)
• Common reasons to replace: wobbling/poor fit on grates, cracks, or persistent sticking from wear

• 1 griddle

• Turn all burners off and let the cooktop cool before placing or removing the griddle
• Position per your model's instructions so it sits flat and secure on the grates
• Preheat gradually on low to medium heat; handle only with oven mitts
• Allow the griddle to cool completely before cleaning or moving

Color: White. Size: 2 oz. can. Porcelain touch-up paint.