Jenn-Air Range Switch

This top burner valve switch mounts to a surface burner gas valve and closes the ignition circuit when you turn the knob to Lite. Replacing a worn switch restores dependable sparking and stops intermittent or nonstop clicking at the burners.

• Mounts on the surface burner valve and closes the ignition circuit at the Lite position
• Signals the spark module to fire the igniters so the burner lights
• Helps ensure quick, consistent burner ignition
• Common symptoms: no spark at a burner, intermittent ignition, or continuous clicking with knobs in Off

• Disconnect power and shut off the gas supply before servicing
• Pull off the burner knob and remove the control/manifold panel to access the valve switch
• Transfer wires one at a time and align the switch correctly on the valve stem; avoid overtightening
• Reassemble, restore power, test for spark with gas off, then relight and check for leaks

Replacement infinite switch that restores variable heat control for a surface heating element on an electric range, letting you adjust burner temperature smoothly and accurately. What it does:

• Regulates power to a surface heating element so the burner produces the selected heat level.
• Replaces a failed or worn rotary control that no longer changes element output.
• Common symptoms: burner won't heat, only heats at one setting, temperature jumps or fluctuates, or knob turns with no effect.
• Fits behind the console and connects to existing element wiring and control knob.

• Disconnect the appliance power before removing the console or control panel to avoid electrical shock.
• Confirm wire locations and take a photo before disconnecting to ensure correct reconnection.
• Secure the switch in place and reconnect wires firmly; test all settings after reassembly.

A replacement switch/ignitor that restores spark ignition so gas burners or the oven will light reliably. Designed to replace a failed ignition switch and help recover consistent sparking for normal appliance operation. What it does:

• Sends the spark needed to ignite gas burners or the oven burner.
• Common symptom: burners or oven won't light or ignition clicks without sparking.
• Can fix intermittent ignition or complete loss of spark at the cooktop/oven.
• Works as the electrical switching/ignition component within the appliance's ignition circuit.

• Disconnect power and shut off the gas supply before beginning any work.
• Handle wires and terminals carefully; avoid bending or damaging the igniter wiring.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage

For switch mounting nut, order part# WP422617.

This burner switch controls the power and heat settings for a surface cooking element, restoring reliable on/off operation, accurate temperature selection, and consistent element cycling on compatible electric ranges. What it does

• Regulates electrical power to a surface burner so the element heats to selected settings and cycles to maintain temperature.
• Replaces a worn or failed switch that causes a burner to not heat, not respond to knob changes, or only work on certain settings.
• Stops intermittent operation or arcing at the switch caused by worn contacts.
• Helps resolve a burner that stays on or will not turn on when the switch is faulty.

• Always disconnect power at the breaker before starting any repair to avoid shock.
• Photograph and/or label wires before removal so you can reconnect terminals correctly.
• Handle terminals gently and ensure secure, tight connections; replace any damaged wiring or connectors.
• Test the range on all heat settings after installation; if you see arcing, burning smell, or continued malfunction, cut power.

Replacement burner switch that controls the heat level for an electric range surface element, restoring proper temperature selection and burner responsiveness. Use this switch when a burner is unresponsive, stuck at one setting, or heats erratically. What it does:

• Regulates power to a surface element so you can select low-to-high heat settings.
• Replaces a failed surface control switch that prevents burners from changing temperature.
• Common symptoms it can fix: burner won't heat, stuck on one setting, no click/response, or inconsistent heat.
• Works as the control interface between the knob and the element on compatible electric ranges.

• Disconnect power at the breaker or unplug the range before starting any repair.
• Photograph or label wires before removal and match terminals exactly when installing the replacement.
• Use insulated tools and avoid contact with live terminals; restore power only after reassembly.

This switch harness assembly connects the control panel switches to the appliance's main wiring, restoring reliable electrical connections for panel buttons and cycle selection. It replaces a damaged or worn harness to help regain consistent control response. What it does:

• Routes power and signals between the control switches and the main control board
• Replaces frayed, broken, or corroded wiring that can cause intermittent or no response from panel buttons
• Helps resolve symptoms like unresponsive controls, intermittent operation, or no-start conditions linked to panel wiring
• Maintains original connector fit and routing for correct switch function

• One switch harness assembly as shown

• Disconnect power (unplug or switch off breaker) before starting any work
• Handle connectors carefully and match connector shapes; do not force or modify terminals
• Verify routing and secure clips to prevent rubbing or pinching against moving parts