Jenn-Air Range Wire, Harness, Power Cord

This replacement dryer power cord supplies electricity from your wall outlet to the dryer's terminal block, providing a secure, reliable connection. Replace a worn or damaged cord to restore dependable power and reduce risk of intermittent shutoffs.

• Supplies electrical power from the outlet to the dryer
• Provides a secure connection at the plug and the dryer's terminal block when properly installed
• Common fixes: dryer won't power on, power cuts out when the unit is moved, or visible damage/heat discoloration on the cord or plug
• Replace if prongs are loose or the insulation is cracked or melted

• Disconnect power at the breaker before servicing and verify the outlet is de-energized
• Follow the dryer's wiring diagram; connect conductors to the correct terminals and tighten securely
• Use an approved strain relief/clamp per the dryer instructions and local electrical codes

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

The Harness-Wire is an OEM part for Whirlpool ranges. It serves as the wiring harness that connects electrical control boards and sensors within the range. 

 Symptoms of a bad harness-wire include:

• Elements or burners that do not heat 
• Issues with switches, controls, or displays failing to work properly
• Recurring range or oven component malfunctions

Causes of a bad harness-wire can be damage from excessive flexing/bending over time, moisture leading to shorts, or failure of crimp/solder connections along the wire.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and signals between appliance controls and electrical components to restore reliable operation. Replaces a damaged, frayed, or burnt harness to help eliminate intermittent or lost power to components. What it does:

• Carries electrical power and control signals between the control board and motors, switches, sensors, or heating elements
• Restores consistent electrical connections when original wiring is damaged, corroded, or pinched
• Addresses symptoms such as components not powering on, intermittent operation, blown fuses, or visible burn/damage at wiring
• Prevents shorting and arcing caused by exposed or broken conductors when replaced promptly

• One wire harness as pictured and specified by the manufacturer

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Match connector shapes and pin counts; route harness clear of sharp edges, heat sources, and moving parts
• Use only the exact replacement harness to maintain proper connector fit and circuit protection
• If you see burned connectors, melted insulation, or a repeatedly tripped breaker, inspect related components and replace damaged parts as needed

This main wiring harness routes power and control signals between the appliance's control assembly and internal components so the unit can operate reliably. It restores electrical connectivity when the original harness is damaged or has failed connections. What it does:

• Provides organized wiring paths for power and signal connections between the control board, user interface, motors, valves, and sensors
• Replaces damaged, frayed, or burned wiring that can cause intermittent operation or complete loss of function
• Helps resolve symptoms such as unresponsive controls, no power to components, or erratic behavior caused by loose or broken wires
• Maintains correct connector pin assignments to ensure each component receives the proper signals

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Compare connectors and wire colors to the existing harness to ensure correct replacement and routing.
• Route and secure the harness to prevent chafing or pinch points; avoid sharp bends.

This wire harness connects key components so your appliance controls and sensors communicate reliably. Replaces a damaged or frayed harness to restore normal electrical connections and help resolve intermittent power or control issues. What it does:

• Routes power and signal connections between the control board, switches, and sensors
• Restores missing or intermittent electrical continuity caused by broken or burned wires
• Helps stop erratic operation, control failures, or no-power conditions linked to damaged wiring
• Matches OEM connector and terminal locations for a direct replacement

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle connectors gently; match keyed plugs and secure all wire routing away from moving parts and sharp edges
• If terminals are corroded or connectors are damaged, replace connectors