Jenn-Air Range Panel Parts

The Bottom Oven Panel is an OEM part for Whirlpool ranges. This panel is located at the bottom of the oven cavity, protecting the internal components and providing a smooth surface for easy cleaning.

Causes of a bad Bottom Oven Panel can include exposure to excessive heat or spills, causing warping, discoloration, or damage to the panel.

Symptoms of a bad Bottom Oven Panel include:

• Visible cracks, dents, or other physical damage
• Discoloration or surface deterioration
• Loose or dislodged panel, exposing internal components

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This Oven Bottom forms the floor of a gas oven cavity. Positioned above the bake burner, it shields the burner/igniter from spills while providing a smooth, removable surface that helps direct heat and is easier to clean.

• Covers and protects the bake burner and igniter assembly
• Helps channel heat and airflow across the oven cavity
• Catches drips and debris; removes for periodic cleaning
• Typical failure signs: warped or rusted panel, flaking finish, burnt-through spots, or persistent smoke from baked-on spills

• Allow the oven to cool completely; wear cut-resistant gloves—edges may be sharp
• Disconnect power and turn off gas supply before servicing
• Remove racks; release rear screws or tabs per your model, lift and slide the old panel out; seat the new panel under the front lip and secure
• Restore power and gas, then verify proper fit and clearance

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

This oven bottom pan replaces the removable bottom tray that catches spills and protects the oven floor, restoring an even surface for cooking and easier cleanup. Fits in the lower cavity under the oven racks. What it does:

• Provides a durable, porcelain-coated surface to catch drips, crumbs and spills during baking and roasting
• Helps prevent spills from contacting the oven floor and heating elements
• Restores a flat, stable cooking surface for pans and bakeware
• Can reduce time spent scrubbing baked-on messes when used with proper liners

• One oven bottom pan

• Allow the oven to cool completely and disconnect power before replacing the pan
• Remove oven racks, slide out the old pan, then slide the replacement into the same position
• No special tools typically required; handle carefully to avoid chipping the coating

This side compartment is a direct-fit door bin that restores storage on the refrigerator door, keeping bottles and small items secure and organized. Durable molded plastic replaces cracked or missing bins for reliable everyday use. What it does:

• Replaces a cracked, broken or missing door bin to restore storage capacity and organization
• Holds bottles, condiments and small containers along the inside of the refrigerator door
• Prevents items from falling when the door opens and closes
• Matches the factory shelf design for correct fit and alignment

• High-level snap-in/screw-in replacement; remove existing bin then install new bin until it seats
• Disconnect power only if removal requires working near electrical components; otherwise power disconnection is not typically needed
• Handle carefully to avoid damage to adjacent door liners or gaskets

This retainer is a small mounting clip that keeps a nearby component held securely in place, helping prevent rattles and misalignment for reliable appliance operation. Install restores proper positioning of the secured part. What it does

• Holds a component or assembly in its intended position to prevent movement or vibration
• Common symptom: loose or rattling parts near the retainer location
• Common symptom: component shifts or comes partially detached during operation
• Works as a replacement for a cracked, broken, or missing retainer that fails to secure the part

• One retainer

• Disconnect power (unplug appliance or switch off circuit breaker) before beginning any repair
• Accessing the retainer may require removing a panel or adjacent parts; keep fasteners organized
• Use basic hand tools; avoid forcing parts to prevent damage to surrounding components

The Control Panel is an OEM part for Whirlpool ranges. It facilitates precise input and display of cooking functions.

Causes of replacement include failure of embedded circuits or damage allowing moisture penetration through the membrane surface over time. Physical impacts can distort switch responsiveness.

Symptoms of issues involve:

• Ghosting or pixelation impairing display readability
• Refusal of elements to toggle through temperature settings
• Unresponsive selection buttons due to circuit interruptions
• Inaccurate temperature calibration requiring technician attention

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement backsplash restores the rear panel that protects the wall behind a freestanding range and gives the appliance a finished appearance. It helps contain splatter and shields wiring and components from spills and debris. What it does:

• Covers the rear opening of the range to protect adjacent walls from grease, steam and food splatter
• Shields wiring and control components located at the back of the appliance
• Restores a clean, finished look when the original panel is dented, rusted or missing
• Helps prevent debris from entering the cabinet and control cavity

• Disconnect power to the range before beginning any work
• Use proper lifting support; a second person may be needed to hold the panel during installation
• Retain and reuse factory screws and fasteners unless replacement hardware is specified
• Handle edges carefully to avoid cuts; align mounting tabs and secure firmly but avoid overtightening