Need Help?
Call or text
Oven won't heat or takes too long to preheat? A weak or failed igniter is the most common cause. Easy DIY repair, typically completed in under 15 minutes.
I used the little video clip shown under the part and replaced it myself. Read more
Oven won't heat or stays at 100°? A weak igniter fails to light the gas. This gas range igniter typically takes 45 minutes to replace with basic tools.
On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more
Oven won't heat or ignite? This igniter kit solves slow heating and ignition failure in gas ovens. Moderate DIY repair in 30-60 minutes.
Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more
If your oven won't heat or igniter glows but gas won't light, the igniter is likely weak. This is a common DIY repair taking 15-30 minutes.
The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more
Burner won't light or spark? This top burner igniter creates the spark to ignite gas on your stovetop. Easy DIY repair in under 5 minutes with a screwdriver.
After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more
Fix an oven that won't light or hold temperature with this gas range igniter. Common repair for clicking sounds without ignition. DIY-friendly, 10-20 min.
Replaced the gas regulator and the oven igniter. It was not a very difficult repair.. most of the parts were easy to get to. The biggest challenge was disconnecting the gas hose from the regulator. It had "pipe dope" (sealant) on the threads. I reconnected with yellow gas pipe tape. Read more
If your burner clicks but won't light, the igniter's ceramic coating may be cracked. This replacement spark electrode typically takes 15-30 minutes.
Replaced igniter---works great---saved service call. Read more
Gas burner won't ignite or spark? This surface burner spark electrode generates the spark to light your cooktop burner. Moderate DIY repair.
Replaced ignitor. Read more
Fix a broil burner that won't light or clicks repeatedly. This spark electrode generates the ignition spark needed for reliable broil operation.
Replaced the igniter. Read more
If your gas burner won't light or clicking but no spark, the spark electrode may be faulty. This part generates the spark to ignite gas burners.
Fix burners that won't spark or click but light with a match. This spark electrode restores ignition on gas cooktops. Typical 15-minute repair.
The burner lit when I used a lighter so figured it was electrical. There were only 2 electrical components so I first tried replacing the block terminal. This did it, very simple and saved $250 on a whole new unit. Read more
If your gas burners won't light or click continuously, a cracked or worn dual-burner igniter is often the cause. Restores reliable ignition to both burners.
Checked the internet for a video on how to fix the igniter. I took the burner apart and replaced the igniter. It works perfectly! Read more
Burner won't spark or light? This range top burner igniter creates the spark to ignite gas burners. Easy 15-minute DIY fix for cracked igniters.
I found the model number on the stove and ordered a replacement. It arrived in two days. I replaced the old one and it works great. Read more
Fix burners that won't light with this spark igniter electrode. Simple DIY repair—hardest part is accessing the back panel. Test for continuity first.
Internet suggested if yellow light happened time to replace. Bought two since I was having trouble with both for years. Would have been nice for a video to exist. The removal was nothing like what is out there and extended the time of the job. Read more
Fix burners that won't light or spark intermittently with a new surface burner igniter. Most DIYers complete this repair in 20 minutes with basic tools.
I disassembled the top of the range and looked at the problem burner. It looked like there was a spark at all three other burners but not the problem burner. There was a visible spark at the connector between the wiring harness and the ceramic igniter but that spark wasn't making it up to the top of the igniter where it can light the burner. I ordered a new igniter for $19 and it was on my doorstep the next day. I replaced the part and now my wife thinks I am a genius. Don't tell her that... Read more
Fix burner clicking or failure to light with a new surface igniter. Restores reliable spark ignition on gas cooktops and ranges. DIY repair in 15 minutes.