Kelvinator Parts

This handle trim replaces a damaged or missing trim piece on the appliance's door handle. It restores a clean, finished look by covering mounting hardware and helps keep the handle properly aligned for everyday use.

• Finishes the end of the door handle and hides visible screws
• Helps stabilize the handle and maintain proper alignment
• Restores appearance when the original trim is cracked, loose, or missing
• Common signs: broken or missing cap, exposed screws, wobbly handle

• Disconnect power before servicing
• Open the door to access the handle; remove the old trim by releasing its clips or fasteners
• Align and snap the new trim into place; transfer any hardware if required
• Do not overtighten fasteners to avoid damaging plastic parts

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Deli Drawer Cover Frame is an OEM part for Frigidaire refrigerators. It serves as the frame that holds and supports the deli drawer cover, ensuring a secure fit and smooth operation. The cover frame is designed to maintain the proper positioning of the deli drawer cover, allowing for easy access to stored items while preserving the overall organization and appearance of the refrigerator interior.

Symptoms of a bad Deli Drawer Cover Frame include:
• Difficulty opening or closing the deli drawer
• Loose or misaligned deli drawer cover
• Cracks, breaks, or visible damage to the cover frame
• Interference with other refrigerator components due to improper fitment

Causes of a damaged or malfunctioning cover frame can include accidental impact, excessive force applied during use, or general wear and tear over time. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This terminal block kit restores a secure, heat-resistant connection point for your appliance's incoming power. Replacing a damaged block helps prevent intermittent power loss and further heat damage from loose or burnt terminals.

• Provides an insulated junction for incoming power leads
• Restores a tight, reliable connection between supply wires and internal wiring
• Helps resolve no power, intermittent power, or visible heat damage at the terminal area
• Replaces cracked, melted, or burned blocks to protect wiring and performance

• Disconnect power at the breaker and verify no voltage is present before servicing
• Label/photograph existing wiring; move one conductor at a time to the new block and tighten terminals securely
• Inspect the cord and wire ends; replace any burnt, brittle, or damaged conductors or lugs before reassembly
• Reinstall covers/strain relief as applicable and verify connections are secure before restoring power

Color: White.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

The Support-Shelf is an OEM part for Frigidaire freezers, designed to provide sturdy and reliable support for the freezer shelves. This part ensures that the shelves remain level and secure under the weight of stored items.

Causes of a bad Support-Shelf can range from overloading shelves beyond their weight capacity, to normal wear and tear from years of use. 

Symptoms of a bad Support-Shelf include:

• Shelves sagging or not sitting level, which can lead to inefficient storage and the risk of items falling.
• Cracks or breaks in the support, compromising the stability of the entire shelving system.
• Difficulty installing or removing shelves, indicating that the supports may be damaged or misshapen.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: White. Used to cover the hinge bearing hole.

Includes one sprayarm.

This door hinge kit replaces worn or broken hinge components so the door opens and closes smoothly and aligns with the latch. It restores proper door support and helps prevent sagging, binding, and misalignment. What it does:

• Maintains correct door alignment at the hinge pivot points
• Helps fix a door that sags, rubs, squeaks, or won't close/latch properly
• Can resolve intermittent operation caused by misaligned latch/interlock engagement
• Direct replacement designed to match the original fit and function

• One hinge kit

• Disconnect power at the breaker or unplug the appliance before servicing
• Support the door during removal and installation to prevent damage or injury
• Note hinge orientation and transfer any reusable hardware from the original
• After installation, verify the door closes evenly and the latch/interlock engages

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

GRILLE/KICKPLATE

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

The Support is an OEM part for Frigidaire refrigerators. This component is designed to provide structural stability and support within the refrigerator, ensuring that various internal parts remain securely in place during operation.

Over time, the support can wear out or become damaged due to regular use, heavy loads, or accidental impacts. Issues such as the refrigerator shelves not staying in place, unusual noises during operation, or visible damage to the support structure are signs that a replacement may be necessary.

Symptoms of a bad support include:

• Shelves not staying in place
• Unusual noises during operation
• Visible damage to the support structure

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.