Kenmore / Sears Cooktop Parts

This is the electronic oven control board that manages bake and broil temperatures, oven timing, and display functions. Replacing a failed control restores accurate temperature regulation and front-panel responsiveness so your range can cook reliably again.

• Regulates oven temperature by cycling bake/broil elements per setpoint
• Controls oven timing functions and user interface/display
• Common failure signs: unresponsive buttons, error codes, inaccurate temps, no heat, or blank/erratic display
• Designed for direct replacement of the original factory control

• Disconnect power at the breaker before servicing
• Transfer overlay and wiring from the old board to the new one, noting connector positions
• Handle the PCB carefully to avoid static discharge and damage
• After installation, run a test bake cycle

Electric range 6 inch surface unit drip bowl. Color: Chrome. It measures about 8 inches in diameter at its widest point at the top. For an 8 inch large drip pan order WB32X106

This replacement surface burner head restores a steady, even flame on your gas cooktop. It mixes gas and air and distributes the flame evenly to help ensure reliable ignition and consistent cooking performance.

• Mounts over the orifice and channels gas/air through flame ports for even heating
• Helps resolve weak, uneven, or yellow flames and delayed ignition
• Can address clicking without lighting or burners that won't stay lit
• Durable cast construction designed for repeated heating cycles

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove grates and access the burner per your model; transfer any mounting hardware from the old part if needed
• Seat the new burner head squarely over the orifice and ensure proper alignment
• Restore gas and power; test for proper ignition and flame. If any gas connections were disturbed, check for leaks with soapy water.

This clock/timer is the range's electronic oven control. It manages the bake and broil circuits using temperature-sensor feedback and provides the digital clock and timer, restoring proper heating performance and a readable display when the original control fails.

• Controls power to bake and broil elements/ignitors to reach and hold the set temperature
• Displays clock, timer, and oven status on the front panel
• Receives keypad inputs to start/stop and adjust oven cycles
• Typical failure signs: blank or dim display, unresponsive controls, error codes, oven will not heat or maintain temperature

• Disconnect power at the breaker before servicing; this control carries live voltage
• Access the control from the backguard/control panel; remove the rear cover to reach mounting screws and connectors
• Photograph or label all wire harness connections; transfer any brackets and install the new board in the same orientation
• Handle electronics by the edges and protect from static discharge; set the clock after reassembly and test oven functions

The Thermal Fuse is an OEM part for Frigidaire ovens and ranges. It acts as a safety device that cuts off power to the appliance if it overheats, preventing potential damage or fire hazards. This fuse ensures that the oven operates within safe temperature limits by shutting down the electrical circuit when necessary.

Causes of a bad thermal fuse can include prolonged exposure to high temperatures, electrical surges, or a malfunctioning oven component that causes overheating. These issues can compromise the integrity of the fuse, rendering it ineffective.

Symptoms of a bad thermal fuse include:

• The oven not heating up
• The oven shutting off unexpectedly during use
• No power to the oven

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Broil Element is an OEM part for Whirlpool wall ovens and ranges. This heating element is responsible for the broiling function of the oven.

Located at the top of the oven cavity, the broil element functions by directing intense radiant heat downward to cook and brown food from above. 

Causes may include natural wear and damage over prolonged high-heat use. Electrical malfunctions inside the element can also cause premature failure. 

Symptoms of a bad broil element include:

• Failure of the broil function
• Diminished or uneven heating during broil cycles
• The presence of cracks, breaks or corrosion on the heating coils

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

By GE. Length - 3.72". Replaces any flat oven igniter (excluding blue ceramic igniters).

Replace worn or damaged cooktop grates with this grate kit to restore a stable, level platform for your pots and pans. It helps maintain safe, consistent pan support and keeps your range or cooktop looking and performing its best. What it does:

• Supports cookware above the burners at the correct height
• Restores level, stable pan support when grates are cracked, warped, or missing
• Helps reduce rocking or tipping of pots and pans
• Common signs it's needed: chips or cracks, grates won't sit flat, unstable cookware

• One grate kit

• Turn off all burners and allow the appliance to cool completely before handling
• Lift off old grates; clean support ledges and burner surrounds
• Position new grates per the burner layout; ensure they sit level and centered
• Verify pan stability before cooking

This assembly combines the spark igniter electrode with the orifice holder for a gas cooktop burner. It restores quick, reliable lighting and consistent burner performance when the original igniter/holder is cracked, shorted, or corroded. What it does:

• Generates the spark to ignite the surface burner gas
• Supports and positions the orifice to deliver gas to the burner head
• Helps resolve no-ignite, intermittent, or delayed ignition at a single burner
• Replaces cracked ceramic, shorted electrodes, and damaged orifice holders

• One surface burner igniter and orifice holder assembly

• Disconnect power and shut off gas supply before servicing
• Remove burner cap and head, then unfasten and lift out the old assembly
• Reconnect the spark wire and mount the new assembly; route the lead away from heat and sharp edges
• Restore gas and power; leak-check connections with an approved solution and verify proper ignition

The Range Leveling Leg is an OEM replacement part for GE ranges and ovens. It is designed to provide stability by allowing the appliance to be leveled on uneven floors. The leveling leg helps ensure the range sits securely, which is critical for even cooking and safe operation.

Over time, leveling legs can become damaged or worn due to frequent adjustments, heavy appliance movement, or environmental factors such as rust or corrosion. This can compromise the range's stability and cooking performance.

Symptoms of a bad leveling leg include:

• The range rocking or wobbling during use
• Difficulty achieving a level cooking surface
• Uneven cooking results due to improper range positioning
• Visible damage to the leveling leg

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: Black. Includes all four knobs. Fits the figure eight shaped shaft.

This adhesive control panel overlay is the faceplate for the electronic oven control on select ranges and wall ovens. It restores readable button labels and a clean, protected surface when the original overlay is faded, bubbled, or damaged.

• Provides printed legends for the keypad buttons and display around the electronic control (EOC)
• Protects the touch surface from wear and cleaning
• Restores a neat, easy-to-read control area
• Typical replacement reasons: peeling, bubbling, cracks, discoloration, or illegible labels

• Disconnect power to the appliance before servicing the control panel
• Remove the control panel/bezel as required to access the old overlay
• Peel off the old overlay; clean and dry the mounting surface before applying the new one
• Align with display and key locations; press from center outward to bond and smooth out air

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

The Surface Burner Cap is an essential OEM component for Frigidaire gas cooktop ranges. It regulates flame spread and directs heat precisely to pots and pans placed above each burner coil.

Causes of burner cap failure include warping or discoloration from continuous exposure to open flames and high cooking temperatures over time. Accidental impacts could also crack or fray burner cap edges.

Symptoms of a faulty burner cap include:

• Irregular or uneven flame patterns beneath cooking vessels   
• Visible yellow or blue flames indicating poor combustion  
• Signs of cracked porcelain or scorched burner bases
• Reduced burner efficiency and poor heat distribution

This authentic OEM replacement is compatible with Electrolux, Gibson, Kelvinator and select Kenmore models. 

This replacement oven door glass restores a clear viewing window and proper heat retention. Replace this pane when the glass is cracked, shattered, or permanently stained to keep your oven safe, efficient, and easy to monitor.

• Forms the inner or outer window of the oven door, sealing heat while letting you watch cooking progress
• Helps maintain temperature stability and preheat performance
• Common failure signs: visible cracks or chips, shattered glass, fogging or residue between panes, or difficulty maintaining temperature
• Restores safety by eliminating sharp edges and reducing risk of further breakage

• Disconnect power and allow the oven to cool completely; shut off gas supply if applicable
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door and glass retainers; note screw and trim orientation
• Transfer any clips/trim from the original pane as needed; reassemble without overtightening and confirm door alignment and seal