Kenmore / Sears Cooktop Parts

This burner head mounts on the cooktop and distributes gas evenly to produce a steady flame. Replacing a worn or damaged head restores proper flame pattern and helps your burner light quickly and cook consistently.

• Directs gas through precisely sized ports to create an even flame
• Can resolve issues like uneven flames, yellow/orange flames, or delayed ignition
• Helps when the burner won't light or only lights partially
• Replaces a corroded, clogged, or warped burner head

• Disconnect power and shut off gas supply before servicing
• Allow the cooktop to cool completely
• Lift off the grate and cap; remove the old head and align the new head on the burner base
• Ensure ports are clean and seated correctly; test for proper ignition and flame

The Broil Element is an OEM part for Whirlpool ranges. This heating element is responsible for providing high heat from the top of the oven, essential for broiling and achieving a crisp, browned finish on dishes.

Common causes of a faulty broil element include wear and tear over time, exposure to high temperatures, or physical damage from cleaning or moving oven racks.

Symptoms of a bad broil element include:

• The broil element not heating up
• Uneven cooking or broiling results
• Visible damage, such as breaks or blisters on the element
• The oven not reaching the desired temperature during broiling

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Stainless)

This replacement thermostat is a temperature-sensitive switch used in select cooking appliances. It opens or closes at a fixed setpoint to control or limit heat, helping protect components and restore dependable operation of the affected circuit. What it does:

• Senses temperature at its mounting point and opens/closes electrical contacts at a designed setpoint
• Controls power to a heating or related circuit (such as an element or fan) to maintain safe operation
• Helps prevent overheating and protects internal components
• Failure can cause no heat, heat that shuts off prematurely, or a related circuit that won't turn on/off

• 1 thermostat

• Disconnect power to the appliance before servicing
• Access location varies by model; refer to your service manual for exact placement
• Move wires one at a time from the old part to the new to maintain correct connections
• Reinstall in the same orientation; ensure firm mounting for proper temperature sensing and secure electrical connections

This surface burner mounts on the cooktop and directs gas to produce a steady, controllable flame. Replace a worn or clogged burner to restore fast ignition and consistent heat from your range's top burner positions.

• Mixes and distributes gas to create the surface cooking flame
• Works with the spark igniter/electrode for reliable lighting
• Helps maintain an even flame pattern and stable heat
• Symptoms can include weak or uneven flames, yellow tips, delayed ignition/repeated clicking, or a burner that won't light

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap, then lift off the old burner; clean the mounting surface
• Align the new burner with the igniter/electrode and locator features; ensure it sits flat and centered
• Reassemble, restore gas/power, and test for proper ignition and a clean, stable flame

This replacement surface element restores proper heating on an electric range or cooktop's top burner. When the original element is open, weak, or damaged, it helps the selected cooking zone reach temperature and heat more evenly.

• Converts electrical power into heat at the chosen surface zone for everyday cooking
• Replaces an element that is open, shorted, or physically damaged
• Common symptoms: surface burner won't heat, heats intermittently, heats very slowly, or shows uneven temperatures
• Works with existing controls to maintain set heat levels

• Disconnect power at the breaker or unplug the appliance; allow the cooktop to cool completely
• Access the element per your model's service procedure (often by lifting the top or accessing from beneath the cooktop)
• Transfer wires one at a time to the matching terminals; secure the element and any brackets as originally installed
• Inspect connectors/wiring for heat damage and address as needed before restoring power and testing

Color: White

The Spring is an OEM part for Whirlpool ranges. This part provides the necessary tension to open and close the oven door smoothly. The spring ensures that the door stays securely shut during cooking and opens effortlessly when needed, contributing to the overall functionality and safety of the range.

Causes of a bad range door spring can include wear and tear over time, exposure to high temperatures, or damage from accidental impacts. 

Symptoms of a bad range door spring include:

• The oven door not staying closed
• Difficulty in opening or closing the door
• Uneven or incomplete sealing of the door
• A door that feels loose or unstable

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement oven door glass restores a clear viewing window and proper heat retention. Replace this pane when the glass is cracked, shattered, or permanently stained to keep your oven safe, efficient, and easy to monitor.

• Forms the inner or outer window of the oven door, sealing heat while letting you watch cooking progress
• Helps maintain temperature stability and preheat performance
• Common failure signs: visible cracks or chips, shattered glass, fogging or residue between panes, or difficulty maintaining temperature
• Restores safety by eliminating sharp edges and reducing risk of further breakage

• Disconnect power and allow the oven to cool completely; shut off gas supply if applicable
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door and glass retainers; note screw and trim orientation
• Transfer any clips/trim from the original pane as needed; reassemble without overtightening and confirm door alignment and seal

This surface burner valve regulates gas flow to a single top burner on your range or cooktop. Replacing a worn valve restores smooth flame control and reliable shutoff for consistent, safe cooking performance.

• Controls gas delivery from the manifold to one surface burner
• Opens/closes with the control knob to ignite and adjust flame height
• Works with the burner's igniter to light and maintain the flame
• Common symptoms: burner won't light, low or uneven flame, flame won't adjust, or a knob that's stiff or spins without control
• Each valve serves one burner position

• Disconnect power, shut off gas supply, and allow the appliance to cool before service
• Note tubing orientation; support the manifold when loosening or tightening fittings
• Use gas-rated thread sealant only if originally used; tighten and check all joints with an approved leak-detection solution
• Restore gas/power and verify proper ignition and flame adjustment on all burners

The Burner Head is an OEM part for Whirlpool ranges. It is responsible for distributing gas to create an even flame for cooking on the stovetop. This burner head ensures efficient gas flow and optimal flame control, which are essential for consistent cooking performance.

Causes of a bad burner head can include clogging from food debris or grease, corrosion due to prolonged exposure to heat and moisture, or physical damage from impact. Such issues can obstruct gas flow and result in uneven heating or poor flame quality.

Symptoms of a bad burner head include:

• Uneven flame or poor flame control
• Difficulty igniting the burner
• Low or inconsistent heat output
• Unusual noises such as hissing or popping during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the adhesive graphic that labels the buttons on the electronic control panel. Replacing a worn, peeling, or unreadable overlay restores a clean look and makes the keypad labels easy to see again.

• Identifies control functions on the electronic oven/range panel
• Adheres to the control face; no electronics are included
• Common fix for worn-off text, bubbling/peeling edges, or cracked graphics
• Helps refresh the panel's appearance after damage or heavy cleaning

• Disconnect power to the appliance before starting
• Remove knob(s)/trim as needed to access the existing overlay
• Carefully peel off the old overlay and clean the surface of residue
• Align and apply the new overlay; press firmly to bond without bubbles

Restore reliable lighting. This ignitor wire harness carries power from the ignition control to the ignitor, replacing cracked or shorted wires that cause weak/no spark or glow so your burner or oven can ignite consistently.

• Provides the dedicated electrical path between the ignition control and the ignitor
• Replaces heat-brittled, cut, or shorted leads to maintain proper insulation
• Helps address: burner or oven won't ignite, intermittent ignition, ignitor won't spark or glow
• Visual clues can include scorched insulation or corroded connectors

• Disconnect power and shut off gas; allow the appliance to cool completely before servicing
• Note original routing and connections; move one connector at a time to avoid cross-wiring
• Route wires away from sharp edges and hot surfaces; secure with original clips/ties
• Ensure all connections are fully seated, then restore power/gas and test ignition

The Door Handle Kit is an OEM replacement part for Frigidaire ovens and ranges. These handles provide safe access to the oven interior.

Causes of a bad handle kit can include normal wear over time of moving parts, accidental damage from impact or mishandling of the oven door, or issues with the latching mechanism.

Symptoms of a bad oven door handle kit include:

• Loose, sluggish, or difficult operation of handles
• Handles detaching from oven door
• Inability to fully open or close the oven door
• Problems with door sealing or staying closed securely

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This spark module powers the surface-burner ignition on gas ranges and cooktops. It generates high-voltage pulses to the electrodes so the burners spark and light when a knob is turned, restoring quick, consistent ignition.

• Sends high-voltage pulses to each surface burner igniter when a burner switch is turned on
• Centralizes spark for multiple burners; a failure often affects more than one burner
• Common symptoms: no clicking/spark on any burners, multiple burners won't light, weak or intermittent spark, continuous clicking from the ignition system
• Helps restore reliable lighting without using matches

• Disconnect electrical power and shut off gas before servicing
• Note wire locations; transfer leads one at a time to matching terminals on the new module
• Mount securely in the original position and ensure proper grounding
• After installation, verify spark at each burner before restoring full operation

The surface element is an OEM part for Whirlpool electric ranges. It is responsible for generating heat through its electric coils or elements on the cooktop. 

Causes of a bad surface element can include wear and tear over time, cracks or damage to the electric coils from heat stress or impact, or failure of the underlying electric components.

Symptoms of a bad surface element include:

• Slow or uneven heating of the cooktop surface
• Hot or cold spots when cooking  
• Elements failing to glow red when turned on
• Burned or charred pans and cookware
• Tripped breakers or blown fuses 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, and some Kenmore electric ranges and cooktops.