Kenmore / Sears Dishrack

This dishwasher rack tine row bracket secures the fold-down tine row to the rack so it pivots and locks correctly. Replacing a cracked or missing bracket helps restore stable plate support and smooth loading.

• Secures the fold-down tine row to the dishrack
• Allows the tine row to pivot between upright and flat positions
• Helps keep dishes from tipping during cycles
• Common symptoms: tines won't stay up, row flops loosely, bracket is cracked/missing

• Disconnect power to the dishwasher before servicing
• Pull out the rack and locate the affected fold-down tine row
• Release the old bracket and snap the new bracket onto the rack wires
• Verify the tine row pivots and latches smoothly before returning the rack

Color: gray. Measures about 3 inches high by 2-1/2 inches deep.

Color: gray. Measures about 3 inches high by 2-1/2 inches deep.

This replacement basket restores organized storage inside your appliance. It securely holds items in place to prevent tipping or falling through, helping you load, access, and clean with confidence.

• Provides a dedicated compartment to keep smaller items contained and upright
• Replaces a cracked, warped, or missing basket
• Helps prevent items from contacting moving parts or obstructing spray/airflow
• Common signs it's time to replace: broken tabs, split seams, or the basket no longer seats correctly

• Disconnect power before servicing
• Open the appliance and remove the old basket; retain any reusable brackets or rack components
• Seat the new basket fully into its designated location
• Do not overload; verify it's stable and clears moving parts before use

The Tine Row Clip is an OEM replacement part for Whirlpool dishwashers. This part secures the lower basket's tine rows in place to properly support dishes during cleaning. The tight fit of the tine row clip is crucial for optimal functionality of the lower dish rack. This clip is used to hold the tines in place on a dishwasher rack.

Causes of a bad tine row clip can include wear and tear leading to cracks or breaks, or damage from impact if the lower rack is mishandled.

Symptoms of a bad tine row clip include:

• Loose or unstable lower dish rack
• Dishes sliding around or falling through the lower rack during the cycle
• Noise from racks or pieces moving inside the tub
• Difficulty loading or removing dishes from the lower rack

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

This replacement dishrack restores secure loading and proper spacing so wash water reaches every item. Replacing a bent or rusty rack helps prevent tipped dishes and marks from flaking rust, and keeps loading/unloading smooth when the rack rollers are intact.

• Holds plates, bowls, and cups in place during wash and rinse cycles
• Maintains spacing for spray coverage and drying airflow
• Rolls in and out along the rails when paired with functional rack rollers
• Common symptoms include broken or bent tines, flaking coating or rust, items tipping, or difficulty sliding the rack

• Disconnect power to the dishwasher before servicing
• Open the door, pull the rack forward, release rack stops/end caps if present, and slide the old rack off the rails
• Transfer any reusable accessories from the old rack to the new rack as required by your model
• Slide the new rack onto the rails, reinstall rack stops, and verify smooth travel before running a cycle

The Tine Row Holder is an OEM part for Whirlpool dishwashers. It is responsible for securing the tines in the dishwasher's rack, keeping them in place to hold dishes, glasses, and utensils securely during the wash cycle.

Over time, the tine row holder can become damaged due to normal wear and tear, repeated loading and unloading of dishes, or accidental mishandling.

Symptoms of a bad tine row holder include:

• Tines that are loose or fall out of place
• Difficulty in loading dishes securely
• Uneven or inadequate cleaning due to improperly spaced items

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Gray. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For white order 675679. To attach these tine tips you will need to order the dishrack gray touch-up paintWP676455.

The Lower Dishrack is an OEM part for Whirlpool dishwashers. It provides space for arranging and securely holding your dishes during the dishwashing cycle.

A bad lower dishwasher dishrack can be caused by regular wear and tear, exposure to hot water and cleaning agents, or accidental damage. If you notice rusting, chipping, or broken tines on the dishrack, it may indicate a problem with the rack itself.

Symptoms of a bad lower dishwasher dishrack include:

• Rust stains or residue on your dishes after a wash cycle
• Difficulty in loading or unloading dishes 
• Unstable or wobbling dishes during the wash cycle
• Limited space or reduced capacity for dishes

Replace your faulty lower dishwasher dishrack with this genuine OEM part to restore your dishwasher. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Note: Right Hand side with release lever.

This is the complete lower dishrack that slides in and out on the tub rails. It provides a stable place to load plates, bowls, and larger cookware on the bottom level and restores smooth rolling and proper dish placement when the original rack is worn or damaged.

• Holds and organizes dishes on the lower level of the dishwasher
• Restores smooth rolling and proper alignment of the lower rack
• Common failure signs include broken or rusted tines, wobbling or derailed rack, and difficulty rolling the rack in/out
• Helps when dishes are not staying in place or the rack no longer supports loads properly

• Disconnect power before servicing
• Pull the old rack straight out of the tub; transfer any usable accessories if applicable
• Slide the new rack onto the existing rail tracks; ensure wheels are seated on both sides
• Test smooth movement and clear door closure before running a cycle

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This rack adjuster assembly restores secure support and adjustable height for the dishwasher's upper rack. Replacing a worn or broken adjuster helps keep the rack level and sliding smoothly for easier loading and consistent wash performance. What it does:

• Supports and locks the upper rack at the selected height
• Allows smooth in-and-out movement when intact
• Helps prevent the upper rack from dropping, tilting, or feeling loose
• Common failure signs: rack won't raise/lower, falls off track, binds or feels rough

• One rack adjuster assembly

• Disconnect power to the dishwasher; shut off water supply
• Pull out the upper rack and remove end caps/stops before lifting the rack off the rails
• Release the old adjuster's locking tabs and install the new assembly in the same orientation
• Reinstall rack stops and test rack height adjustment and movement before restoring power

The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack. 

Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.

Symptoms of a bad track include:  

• Rack that will not fully extend or retract
• Binding or sticking during rack movement  
• Rack that will not stay positioned above

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.