Kenmore / Sears Dishwasher Control Board

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.

The is is a dishwasher control board. This part is tasked with controlling all of the internal parts of the dishwasher. It regulates the wash cycle, drying cycle, and other parts of a typical washing cycle. This part has many internal components and can become damaged over time or through use. If the dishwasher does not run, starts a cycle but doesn't finish it, or otherwise has functioning issues, this could mean the control board should be replaced.Before starting, make sure the dishwasher is unplugged for safety reasons. Open the door and remove the screws from the inner panel. Separate the panels while disconnecting the wire harness from the control panel. Pull the outer door panel and control panel off the appliance. Install the new part and reconnect wires and ribbons before reassembling the dishwasher. Plug in the appliance and test it.This is a genuine OEM replacement part designed to be compatible with dishwashers by Kenmore and Whirlpool. The control board comes directly from the manufacturer and is sold as a single component.

This main electronic control board governs the appliance's user interface and cycle functions, restoring responsive controls and correct operation when the original board fails. Replace a faulty control board to correct erratic or unresponsive behavior. What it does:

• Receives input from the console and sends control signals to relays, valves, motors and sensors.
• Restores normal cycle selection and timing when a failed board prevents the appliance from starting or completing cycles.
• Addresses symptoms like unresponsive or non-working buttons, blank or erratic displays, and unexpected program changes.
• Interfaces with safety and feedback sensors to coordinate appliance functions.

• Always disconnect power to the appliance before replacing the control board to avoid shock or damage.
• Handle the board by its edges and avoid touching circuit traces or components; the board is static-sensitive.
• Note connector locations or photograph wiring before removal to ensure correct reassembly.

Restore your dishwasher's brains with this control assembly. It manages cycle selection and timing so the machine responds to commands, starts reliably, and completes wash cycles without random beeps, stalls, or unresponsive controls.

• Coordinates cycle logic and component operation
• Interprets button/touch inputs from the console
• Drives status indicators or display on applicable models
• Typical symptoms: controls unresponsive, won't start, lights flicker or beep erratically, cycle won't advance

• Disconnect power at the breaker before servicing
• Use anti-static precautions; handle the board by its edges and avoid touching contacts
• Label/photograph wiring; move connectors one at a time and fully seat any ribbon cables/locks
• Reuse existing mounting hardware; ensure correct orientation and secure harness routing before reassembly

This electronic control is the refrigerator's main control board that manages temperature, user display, and timed functions to restore reliable operation. Replaces a failed control to return the unit to normal cycle and user control. What it does:

• Regulates compressor, fans, and defrost cycles based on sensor inputs
• Powers and responds to the front control/display panel for temperature and mode settings
• Controls timed functions such as automatic defrost and ice maker cycles
• Resolves symptoms like unresponsive controls, incorrect temperatures, or intermittent cooling behaviors

• One electronic control (main control board)

• Disconnect power to the appliance before starting any work
• Handle the board by its edges and avoid touching components; discharge static by grounding yourself
• Reassemble panels and secure all connectors; restore power and run a function test

This electronic control board replaces the oven's main control module to restore user interface and timed bake/clock functions. It provides the control logic that manages heating cycles and display feedback for the range. What it does:

• Serves as the oven's primary control module, interpreting commands from the touchpad or knobs
• Controls bake/broil elements, timers, and display outputs through relay/signaling circuits
• Common symptoms: blank or unresponsive display, no heat or heating cycles won't start, or controls do not respond
• Replaces a failed or intermittent board that causes erratic oven behavior

• One electronic control board assembly

• Disconnect power at the breaker before beginning service to avoid shock or injury
• Handle the board carefully and avoid touching connector pins or components; static discharge can damage electronics
• Verify wire harness orientation and secure all connectors before restoring power.

This electromechanical timer controls cycle selection and timing for your appliance, restoring proper step progression and cycle operation. It replaces a worn or failed timer to help get your appliance cycling again. What it does

• Advances and times wash/dry cycles based on the selected program.
• Re-establishes cycle control when the timer motor or cam contacts fail.
• Commonly used when cycles won't advance, the appliance won't start a timed cycle, or settings don't change.
• Works as the user-operated timing/control mechanism for mechanical cycle selection.

• One electromechanical timer assembly.

• Disconnect power before starting — shock risk. If the appliance is gas, also shut off the gas supply.
• Requires panel access and basic wiring knowledge; note wire locations or take a photo before disconnecting.
• Tighten fasteners and confirm wiring connections are secure; test operation with power restored.

This electronic control module manages a range of oven/cooktop functions so the appliance responds correctly to front-panel commands and control inputs. Replacing a failed module restores normal control and display operation. What it does:

• Receives input from touchpads/knobs and sends signals to heating elements, relays, and sensors
• Controls oven timing, temperature setpoints, and cycle sequencing
• Powers or drives the display and indicator lights when working properly
• A failed module can cause unresponsive controls, blank or erratic displays, or interrupted heating cycles

• Disconnect all power to the appliance before starting work to avoid shock or damage
• Handle the board by its edges and avoid static discharge; wear a grounded wrist strap if available
• Verify connector orientation and seating; do not force connectors or components

The OEM Electronic Control Board is an OEM replacement part for Whirlpool dishwashers. It is a circuit board that controls all of the functions of the dishwasher, including the wash cycles, water temperature, and detergent dispensing.

Causes of failure involve damage from liquid intrusion shortening circuits or component deterioration over extended use reducing precision.

Symptoms include:

• Dishwasher fails to start selected cycle
• Lights, displays or programming malfunctions
• No response from control buttons
• Dishwasher appears dead or powerless

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This electronic control board is the appliance's central controller. It interprets user inputs and sensor signals to power components at the right time, restoring reliable operation when the original board fails.

• Interprets user settings and manages cycle timing and temperature control
• Switches relays/outputs to run motors, heaters, valves, fans, and lights
• Interfaces with sensors and safety switches to protect the appliance
• Symptoms can include no display or response, won't start, cycles that won't advance, or erratic operation
• Logs diagnostic error codes to aid troubleshooting

• Disconnect power before servicing; follow ESD precautions and handle the board by the edges
• Access the control area, then note/photograph wiring and move connectors one at a time to the new board
• Mount securely, ensure no wires are pinched, reassemble, and restore power
• Run a diagnostic or test cycle to confirm normal operation

This rotary timer controls the sequence and length of dryer cycles so your machine advances through timed heating, cool-down, and drum-turn stages. It restores reliable cycle progression and timing when the original timer fails. What it does:

• Advances the dryer through selected cycles and timing intervals
• Turns power to the heating and motor circuits on/off at the correct points in a cycle
• Helps resolve symptoms like cycles that won't advance, the dryer stopping mid-cycle, or no heat occurring during timed cycles
• Works as the main user-programmable timing control for mechanical/timer-based dryers

• Turn power to the appliance off at the breaker before starting work to avoid shock.
• Handle the timer carefully to avoid bending terminals; match connector locations during reassembly.
• Some disassembly of the dryer console or control housing is required; keep track of screws and panel clips.

This electromechanical timer controls and advances the appliance's wash/dry cycles so clothes complete the selected program. Replaces a worn or failed timing unit to restore cycle sequencing and program selection. What it does:

• Rotates and switches internal contacts to advance cycles and engage components at the correct times
• Restores timed functions like wash, rinse, spin, or dry
• Commonly used when the appliance won't complete programs, stops mid-cycle, or selector changes have no effect
• Works with the console controls to select and maintain the chosen program settings

• Disconnect power (and gas supply for gas dryers) before starting any work
• Requires basic hand tools and removal of the control panel or console for access
• Note knob and dial positions before removal to preserve selector alignment
• Test appliance operation after installation to confirm correct cycle advancement